22483: EDF 2772 SMESH: Define several 3D viscous layer hypotheses on the same Geometry

doc/salome/gui/SMESH/input/1d_meshing_hypo.doc

@@ -183,28 +183,48 @@ You can set the type of distribution for this hypothesis in the
 <br><b>Equidistant Distribution</b> - all segments will have the same
 length, you define only the <b>Number of Segments</b>.
 
-<br><b>Scale Distribution</b> - length of segments gradually changes depending on the <b>Scale Factor</b>, which is a ratio of the first segment length to the last segment length.
+<br><b>Scale Distribution</b> - length of segments gradually changes
+depending on the <b>Scale Factor</b>, which is a ratio of the first
+segment length to the last segment length.<br>
+Length of segments changes in geometric progression with the common
+ratio (A) depending on the <b>Scale Factor</b> (S) and <b>Number of
+Segments</b> (N) as follows: <code> A = S**(1/(N-1))</code>. For an
+edge of length L, length of the first segment is 
+<code>L * (1 - A)/(1 - A**N)</code>.
+
 
 \image html a-nbsegments2.png
 
+<br><b>Distribution with Analytic Density</b> - you input the formula,
+which will rule the change of length of segments and the module shows
+in the plot the density function curve in red and the node
+distribution as blue crosses.
+
+\image html distributionwithanalyticdensity.png
+
+<br>
+\anchor analyticdensity_anchor
+The node distribution is computed so that to have the density function
+integral on the range between two nodes equal for all segments.
+\image html analyticdensity.png
+
 <br><b>Distribution with Table Density</b> - you input a number of
 pairs <b>t - F(t)</b>, where \b t ranges from 0 to 1, and the module computes the
 formula, which will rule the change of length of segments and shows
-the curve in the plot. You can select the <b>Conversion mode</b> from
+in the plot the density function curve in red and the node
-\b Exponent and <b>Cut negative</b>.
+distribution as blue crosses. The node distribution is computed the
+same way as for 
+\ref analyticdensity_anchor "Distribution with Analytic Density". You
+can select the <b>Conversion mode</b> from\b Exponent and <b>Cut
+negative</b>. 
 
 \image html distributionwithtabledensity.png
 
-<br><b>Distribution with Analytic Density</b> - you input the formula,
-which will rule the change of length of segments and the module shows
-the curve in the plot.
-
-\image html distributionwithanalyticdensity.png
-
 <b>See Also</b> a sample TUI Script of a 
 \ref tui_deflection_1d "Defining Number of Segments" hypothesis
 operation.
 
+
 <br>
 \anchor start_and_end_length_anchor
 <h2>Start and End Length hypothesis</h2>

doc/salome/gui/SMESH/input/additional_hypo.doc

@@ -93,7 +93,7 @@ computations.
   and edges, just hide the mesh to avoid this. To avoid a long wait when a
   geometry with many faces (or edges) is displayed, the number of faces
   (edges) shown at a time is limited by the value of "Sub-shapes
-  preview chunk size" preference (in Preferences/Mesh/General tab).<br>
+  preview chunk size" preference (in Preferences/Mesh/General tab).
 
   If faces/edges without layers are specified, the element layers are
   not constructed on geometrical faces shared by several solids in 3D
@@ -106,6 +106,15 @@ computations.
   possibly being internal faces/edges within the whole model.
   \image html viscous_layers_on_submesh.png 2D viscous layers constructed on boundary edges of a sub-mesh on a disk face.
 
+  If you use \b several hypotheses to define viscous layers on faces of
+  one solid, keep in mind the following. Each hypothesis defines a set
+  of faces with viscous layers (even if you specify faces without
+  layers). The sets of faces with viscous layers defined by several
+  hypotheses should not intersect, else the module won't add an
+  hypothesis that is incompatible with another one. <br>
+  Also you can't define different number of layers on adjacent faces
+  of a solid.<br>
+  This logic is also valid for the 2D hypothesis.
 </li>
 </ul>
 

doc/salome/gui/SMESH/input/constructing_meshes.doc

@@ -29,9 +29,13 @@
     \image html createmesh-inv.png
     <br>
   </li>
-  <li>Select <b>Mesh Type</b> in the corresponding list from <b>Any, Hexahedral, Tetrahedral, Triangular </b> and \b Quadrilateral (there can be less items for lower dimensions). 
+  <li> To filter off irrelevant meshing algorithms, you can
+    select <b>Mesh Type</b> in the corresponding list from <b>Any,
+      Hexahedral, Tetrahedral, Triangular </b> and \b Quadrilateral (there
+    can be less items for the geometry of lower dimensions).
 
-  Selection of a mesh type hides any algorithms that are not able to create elements of this type.</li>
+    Selection of a mesh type hides all meshing algorithms that can not
+    generate elements of this type.</li>
 
   <li>Apply \subpage basic_meshing_algos_page "meshing algorithms" and
     \subpage about_hypo_page "hypotheses" which will be used to compute
@@ -42,7 +46,8 @@
     dimension of the CAD model (geometry) the algorithms listed on
     this page affect and the maximal dimension of elements the algorithms
     generate. For example, \b 3D page lists the algorithms that affect
-    3D geometrical objects (solids).
+    3D geometrical objects (solids) and generate 3D mesh elements
+    (tetrahedra, hexahedra etc.)
 
     \note
     - Some page(s) can be disabled if the source geometrical
@@ -65,7 +70,6 @@
     it is "Mesh_1". Then select the geometrical object you wish to
     mesh in the Object Browser and click "Select" button near \b Geometry
     field (if the name of the object has not yet appeared in \b Geometry field).
-
     <center>
     \image html image120.png
     <em>"Select" button</em>
@@ -74,21 +78,22 @@
     Now you can define 3D Algorithm and 3D Hypotheses, which will be
     applied to the solids of your geometrical object. Click the <em>"Add
       Hypothesis"</em>  button to add a hypothesis.
-
     <center>
     \image html image121.png
     <em>"Add Hypothesis" button</em>
     </center>
+    Click the <em>"Plus"</em> button to enable adding more additional hypotheses.
 
     Click the <em>"Edit Hypothesis"</em> button to change the values for the
     current hypothesis.
-
     <center>
     \image html image122.png
     <em>"Edit Hypothesis" button</em>
     </center>
 
-    Most 2D and 3D algorithms can work without hypotheses using default meshing parameters. Some algorithms do not require any hypotheses. After selection of an algorithm "Hypothesis" field of
+    Most 2D and 3D algorithms can work without hypotheses using
+    default meshing parameters. Some algorithms do not require any
+    hypotheses. After selection of an algorithm "Hypothesis" field of
     the dialog can contain:
     <ul>
       <li> <em>\<Default\></em> if the algorithm can work using default
@@ -111,6 +116,9 @@
     choice of hypotheses and lower dimension algorithms depends on
     the higher dimension algorithm.
 
+    If you wish you can select different algorithms and/or hypotheses
+    for meshing some parts of your CAD model by \ref constructing_submeshes_page.
+
     Some algorithms generate mesh of several dimensions, while others
     produce mesh of only one dimension. In the latter case there must
     be one Algorithm and zero or several
@@ -128,8 +136,9 @@
 
     It contains: 
     <ul>
+      <li>a mesh name (<em>Mesh_mechanic</em>);
       <li>a reference to the geometrical object on the basis of
-        which the mesh has been constructed;</li> 
+        which the mesh has been constructed (\a mechanic);</li> 
       <li><b>Applied hypotheses</b> folder containing the references
         to the hypotheses applied at the construction of the mesh;</li>
       <li><b>Applied algorithms</b> folder containing the references

doc/salome/gui/SMESH/input/constructing_submeshes.doc

@@ -2,7 +2,7 @@
 
 \page constructing_submeshes_page Constructing sub-meshes
 
-Sub-mesh is a mesh on a geometrical sub-object created with algorithms
+Sub-mesh is a mesh on a geometrical sub-object created with meshing algorithms
 and/or hypotheses other than the algorithms and hypotheses assigned to
 the parent mesh on the parent geometrical object.
 
@@ -52,7 +52,7 @@ The following dialog box will appear:
 \par
 It allows to define the \b Name, the parent \b Mesh and the \b
 Geometry (e.g. a face if the parent mesh has been built on box) of the
-sub-mesh. You can define algorithms and hypotheses in the same way as
+sub-mesh. You can select meshing algorithms and hypotheses in the same way as
 in \ref constructing_meshes_page "Create mesh" menu.
 
 \par
@@ -93,11 +93,13 @@ displayed as follows:
 \par
 It contains:
 <ul>
-<li>a reference to the geometrical object on the basis of which the sub-mesh has been constructed;</li>
+<li>a sub-mesh name (\a SubMeshFace1)
+<li>a reference to the geometrical object on the basis of which the
+  sub-mesh has been constructed (<em>Cylindrical Face_1</em>);</li>
 <li><b>Applied hypotheses</b> folder containing the references to the
-hypotheses applied to the construction of the sub-mesh;</li>
+hypotheses selected at the construction of the sub-mesh;</li>
 <li><b>Applied algorithms</b> folder containing the references to the
-algorithms applied to the construction of the sub-mesh.</li>
+algorithms selected at the construction of the sub-mesh.</li>
 </ul>
 
 <br><b>See Also</b> a sample TUI Script of a 

doc/salome/gui/SMESH/input/creating_groups.doc

@@ -40,29 +40,24 @@ the following ways:
   mesh. For this, turn on the <b>Select All</b> check box. In this mode
   all controls, which allow selecting the entities in other ways, are
   disabled.</li>
-<li>By applying the Filter. The <b>Set filter</b> button allows to
-  define the filter for selection of the elements for your group. See more
-  about filters on the 
-  \ref selection_filter_library_page "Selection filter library" page.<br>
-  If the <b>Enable manual edition</b> check box is turned off, the 
-  filter entirely defines the group contents. In this mode, the filter is
-  applied to all elements of the mesh. If there are no entities
-  corresponding to the filter, the \b Apply button is disabled.<br>
-  If the <b>Enable manual edition</b> check box is turned on, the defined
-  filter can be used to for selection of entities for the group.</li>
 <li>By choosing entities manually with the mouse in the 3D Viewer. For
   this, turn on the <b>Enable manual edition</b> check box. You can
   click on an element in the 3D viewer and it will be highlighted. After
   that click the \b Add button and the ID of this element will be
-  added to the list.</li>
+  added to the list.<br>
-<li>By adding entities from either a submesh or an existing
+  The <b>Set filter</b> button allows to define the filter for
+  selection of the elements for your group. See more about filters on
+  the \ref selection_filter_library_page "Selection filter library"
+  page.</li> 
+<li>By adding entities from either a sub-mesh or an existing
   group.  For this, turn on the <b>Enable manual edition</b> check
-  box. <b>Select from</b> set of fields allows to select a submesh or
+  box. <b>Select from</b> set of fields allows to select a sub-mesh or
   a group of the appropriate type.</li>
 </ul>
 In the <b>manual edition</b> mode you can
 <ul>
-<li>click the \b Remove button to remove the selected elements from the list</li>
+<li>click the \b Remove button to remove the selected list items from
+  the list.</li>
 <li>click the <b>Sort List</b> button to sort the list of IDs of 
   mesh elements.</li>
 </ul>

doc/salome/gui/SMESH/input/editing_meshes.doc

@@ -2,11 +2,11 @@
 
 \page editing_meshes_page Editing Meshes
 
-\n After you have created a mesh or submesh with definite applied
+\n After you have created a mesh or sub-mesh with definite applied
-hypotheses and algorithms you can edit your mesh by \b assigning new
+meshing algorithms and hypotheses you can edit your mesh by \b assigning other
-hypotheses and algorithms or \b unassigning the applied hypotheses and
+algorithms and/or hypotheses or \b unassigning the applied hypotheses and
-algorithms. The editing proceeds in the same way as <b>Mesh
+algorithms. The editing proceeds in the same way as 
-Creation</b>.
+\ref create_mesh_anchor "Mesh Creation".
 
 \image html createmesh-inv3.png
 

idl/SMESH_Mesh.idl

@@ -215,7 +215,8 @@ module SMESH
     HYP_BAD_DIM,      // bad dimension
     HYP_BAD_SUBSHAPE, // shape is neither the main one, nor its sub-shape, nor a group
     HYP_BAD_GEOMETRY, // geometry mismatches algorithm's expectation
-    HYP_NEED_SHAPE    // algorithm can work on shape only
+    HYP_NEED_SHAPE,   // algorithm can work on shape only
+    HYP_INCOMPAT_HYPS // several additional hypotheses are incompatible one with other
   };
 
   /*!
@@ -508,24 +509,22 @@ module SMESH
       raises (SALOME::SALOME_Exception);
 
     /*!
-     * Add hypothesis to the mesh, under a particular Sub-shape
+     * Add hypothesis to the mesh, under a particular sub-shape
      * (or the main shape itself)
-     * The Add method is only used to prepare the build of the mesh and store
+     * This method is only used to prepare the build of the mesh and store
      * the algorithms and associated parameters.
-     * Actual job of mesh the shape is done by MESH_Gen.
+     * Actual job of meshing the shape is done by SMESH_Gen::Compute()
      * @params
-     * - aSubShape : sub-shape obtained by a shape explode in GEOM
+     * - aSubObject : sub-shape obtained by a shape explode in GEOM
      *   (or main shape)
-     * - anHyp : hypothesis object
+     * - anHyp : an hypothesis object
      * @return
-     * - OK if the hypothesis is compatible with the sub-shape
+     * - An enum item explaining what's up
-     *   (and all previous hypothesis on the sub-shape)
+     * - anErrorText: an optional textual description of a problem (if any)
-     * - NOK if the hypothesis is not compatible with the sub-shape
-     *   (or one previous hypothesis on the sub-shape)
-     * raises exception if hypothesis has not been created
      */
     Hypothesis_Status AddHypothesis(in GEOM::GEOM_Object aSubObject,
-				    in SMESH_Hypothesis anHyp)
+                                    in SMESH_Hypothesis  anHyp,
+                                    out string           anErrorText)
       raises (SALOME::SALOME_Exception);
 
     /*!

resources/CMakeLists.txt

@@ -44,6 +44,8 @@ SET(SMESH_RESOURCES_FILES
   mesh_hypo_segment.png
   mesh_hypo_volume.png
   mesh_hypo_edit.png
+  mesh_plus.png
+  mesh_minus.png
   mesh_info.png
   advanced_mesh_info.png
   standard_mesh_info.png

src/SMESH/SMESH_Algo.hxx

@@ -138,6 +138,8 @@ class SMESH_EXPORT SMESH_Algo : public SMESH_Hypothesis
     * \param aShape - the shape
     * \param aStatus - check result
     * \retval bool - true if hypothesis is well defined
+    *
+    * Textual description of a problem can be stored in _comment field.
    */
   virtual bool CheckHypothesis(SMESH_Mesh&                          aMesh,
                                const TopoDS_Shape&                  aShape,

src/SMESH/SMESH_Hypothesis.hxx

@@ -63,7 +63,8 @@ public:
     HYP_BAD_DIM,      // bad dimension
     HYP_BAD_SUBSHAPE, // shape is neither the main one, nor its sub-shape, nor a group
     HYP_BAD_GEOMETRY, // shape geometry mismatches algorithm's expectation
-    HYP_NEED_SHAPE    // algorithm can work on shape only
+    HYP_NEED_SHAPE,   // algorithm can work on shape only
+    HYP_INCOMPAT_HYPS // several additional hypotheses are incompatible one with other
   };
   static bool IsStatusFatal(Hypothesis_Status theStatus)
   { return theStatus >= HYP_UNKNOWN_FATAL; }

src/SMESH/SMESH_Mesh.cxx

@@ -602,11 +602,15 @@ SMESH_ComputeErrorPtr SMESH_Mesh::GMFToMesh(const char* theFileName,
 
 SMESH_Hypothesis::Hypothesis_Status
 SMESH_Mesh::AddHypothesis(const TopoDS_Shape & aSubShape,
-                            int                  anHypId  ) throw(SALOME_Exception)
+                          int                  anHypId,
+                          std::string*         anError  ) throw(SALOME_Exception)
 {
   Unexpect aCatch(SalomeException);
   if(MYDEBUG) MESSAGE("SMESH_Mesh::AddHypothesis");
 
+  if ( anError )
+    anError->clear();
+
   SMESH_subMesh *subMesh = GetSubMesh(aSubShape);
   if ( !subMesh || !subMesh->GetId())
     return SMESH_Hypothesis::HYP_BAD_SUBSHAPE;
@@ -633,11 +637,14 @@ SMESH_Hypothesis::Hypothesis_Status
 
   // shape
 
-  bool isAlgo = ( !anHyp->GetType() == SMESHDS_Hypothesis::PARAM_ALGO );
+  bool isAlgo = ( anHyp->GetType() != SMESHDS_Hypothesis::PARAM_ALGO );
   int   event = isAlgo ? SMESH_subMesh::ADD_ALGO : SMESH_subMesh::ADD_HYP;
 
   SMESH_Hypothesis::Hypothesis_Status ret = subMesh->AlgoStateEngine(event, anHyp);
 
+  if ( anError && SMESH_Hypothesis::IsStatusFatal(ret) && subMesh->GetComputeError() )
+    *anError = subMesh->GetComputeError()->myComment;
+
   // sub-shapes
   if ( !SMESH_Hypothesis::IsStatusFatal(ret) &&
        anHyp->GetDim() <= SMESH_Gen::GetShapeDim(aSubShape)) // is added on father
@@ -645,9 +652,19 @@ SMESH_Hypothesis::Hypothesis_Status
     event = isAlgo ? SMESH_subMesh::ADD_FATHER_ALGO : SMESH_subMesh::ADD_FATHER_HYP;
 
     SMESH_Hypothesis::Hypothesis_Status ret2 =
-      subMesh->SubMeshesAlgoStateEngine(event, anHyp);
+      subMesh->SubMeshesAlgoStateEngine(event, anHyp, /*exitOnFatal=*/true);
     if (ret2 > ret)
+    {
       ret = ret2;
+      if ( SMESH_Hypothesis::IsStatusFatal( ret ))
+      {
+        if ( anError && subMesh->GetComputeError() )
+          *anError = subMesh->GetComputeError()->myComment;
+        // remove anHyp
+        event = isAlgo ? SMESH_subMesh::REMOVE_ALGO : SMESH_subMesh::REMOVE_HYP;
+        subMesh->AlgoStateEngine(event, anHyp);
+      }
+    }
 
     // check concurent hypotheses on ancestors
     if (ret < SMESH_Hypothesis::HYP_CONCURENT && !isGlobalHyp )
@@ -892,17 +909,20 @@ int SMESH_Mesh::GetHypotheses(const SMESH_subMesh *               aSubMesh,
     const TopoDS_Shape & aSubShape = aSubMesh->GetSubShape();
     const list<const SMESHDS_Hypothesis*>& hypList = _myMeshDS->GetHypothesis(aSubShape);
     for ( hyp = hypList.begin(); hyp != hypList.end(); hyp++ )
-      if ( aFilter.IsOk (cSMESH_Hyp( *hyp ), aSubShape) &&
+    {
-           ( cSMESH_Hyp(*hyp)->IsAuxiliary() || !mainHypFound ) &&
+      const SMESH_Hypothesis* h = cSMESH_Hyp( *hyp );
-           hypTypes.insert( (*hyp)->GetName() ).second )
+      if (( aFilter.IsOk( h, aSubShape )) &&
+          ( h->IsAuxiliary() || !mainHypFound ) &&
+          ( h->IsAuxiliary() || hypTypes.insert( h->GetName() ).second ))
       {
         aHypList.push_back( *hyp );
         nbHyps++;
-        if ( !cSMESH_Hyp(*hyp)->IsAuxiliary() )
+        if ( !h->IsAuxiliary() )
           mainHypFound = true;
         if ( assignedTo ) assignedTo->push_back( aSubShape );
       }
     }
+  }
 
   // get hypos from ancestors of aSubShape
   if ( andAncestors )
@@ -918,18 +938,21 @@ int SMESH_Mesh::GetHypotheses(const SMESH_subMesh *               aSubMesh,
       const TopoDS_Shape& curSh = (*smIt)->GetSubShape();
       const list<const SMESHDS_Hypothesis*>& hypList = _myMeshDS->GetHypothesis(curSh);
       for ( hyp = hypList.begin(); hyp != hypList.end(); hyp++ )
-        if (( aFilter.IsOk( cSMESH_Hyp( *hyp ), curSh ))         &&
+      {
-            ( cSMESH_Hyp(*hyp)->IsAuxiliary() || !mainHypFound ) &&
+        const SMESH_Hypothesis* h = cSMESH_Hyp( *hyp );
-            ( hypTypes.insert( (*hyp)->GetName() ).second          ))
+        if (( aFilter.IsOk( h, curSh )) &&
+            ( h->IsAuxiliary() || !mainHypFound ) &&
+            ( h->IsAuxiliary() || hypTypes.insert( h->GetName() ).second ))
         {
           aHypList.push_back( *hyp );
           nbHyps++;
-          if ( !cSMESH_Hyp(*hyp)->IsAuxiliary() )
+          if ( !h->IsAuxiliary() )
             mainHypFound = true;
           if ( assignedTo ) assignedTo->push_back( curSh );
         }
       }
     }
+  }
   return nbHyps;
 }
 

src/SMESH/SMESH_Mesh.hxx

@@ -126,7 +126,7 @@ public:
                                   bool        theMakeRequiredGroups = true );
 
   SMESH_Hypothesis::Hypothesis_Status
-  AddHypothesis(const TopoDS_Shape & aSubShape, int anHypId)
+  AddHypothesis(const TopoDS_Shape & aSubShape, int anHypId, std::string* error=0)
     throw(SALOME_Exception);
   
   SMESH_Hypothesis::Hypothesis_Status

src/SMESH/SMESH_subMesh.cxx

@@ -670,11 +670,17 @@ bool SMESH_subMesh::IsApplicableHypotesis(const SMESH_Hypothesis* theHypothesis,
   return false;
 }
 
-//=============================================================================
+//================================================================================
 /*!
+ * \brief Treats modification of hypotheses definition
+ *  \param [in] event - what happens
+ *  \param [in] anHyp - a hypothesis
+ *  \return SMESH_Hypothesis::Hypothesis_Status - a treatment result.
  * 
+ * Optional description of a problematic situation (if any) can be retrieved
+ * via GetComputeError().
  */
-//=============================================================================
+//================================================================================
 
 SMESH_Hypothesis::Hypothesis_Status
   SMESH_subMesh::AlgoStateEngine(int event, SMESH_Hypothesis * anHyp)
@@ -753,7 +759,7 @@ SMESH_Hypothesis::Hypothesis_Status
     if ( ! CanAddHypothesis( anHyp )) // check dimension
       return SMESH_Hypothesis::HYP_BAD_DIM;
 
-    if ( /*!anHyp->IsAuxiliary() &&*/ getSimilarAttached( _subShape, anHyp ) )
+    if ( !anHyp->IsAuxiliary() && getSimilarAttached( _subShape, anHyp ) )
       return SMESH_Hypothesis::HYP_ALREADY_EXIST;
 
     if ( !meshDS->AddHypothesis(_subShape, anHyp))
@@ -782,6 +788,9 @@ SMESH_Hypothesis::Hypothesis_Status
   if (!isApplicableHyp)
     return ret; // not applicable hypotheses do not change algo state
 
+  if (( algo = GetAlgo()))
+    algo->InitComputeError();
+
   switch (_algoState)
   {
 
@@ -1114,6 +1123,11 @@ SMESH_Hypothesis::Hypothesis_Status
     }
   }
 
+  if ( _algo ) { // get an error description set by _algo->CheckHypothesis()
+    _computeError = _algo->GetComputeError();
+    _algo->InitComputeError();
+  }
+
   bool stateChange = ( _algoState != oldAlgoState );
 
   if ( stateChange && _algoState == HYP_OK ) // hyp becomes OK
@@ -1213,14 +1227,24 @@ void SMESH_subMesh::setAlgoState(algo_state state)
   _algoState = state;
 }
 
-//=============================================================================
+//================================================================================
 /*!
+ * \brief Send an event to sub-meshes
+ *  \param [in] event - the event
+ *  \param [in] anHyp - an hypothesis
+ *  \param [in] exitOnFatal - to stop iteration on sub-meshes if a sub-mesh
+ *              reports a fatal result
+ *  \return SMESH_Hypothesis::Hypothesis_Status - the worst result
  *
+ * Optional description of a problematic situation (if any) can be retrieved
+ * via GetComputeError().
  */
-//=============================================================================
+//================================================================================
+
 SMESH_Hypothesis::Hypothesis_Status
   SMESH_subMesh::SubMeshesAlgoStateEngine(int                event,
-                                          SMESH_Hypothesis * anHyp)
+                                          SMESH_Hypothesis * anHyp,
+                                          bool               exitOnFatal)
 {
   SMESH_Hypothesis::Hypothesis_Status ret = SMESH_Hypothesis::HYP_OK;
   //EAP: a wire (dim==1) should notify edges (dim==1)
@@ -1229,10 +1253,16 @@ SMESH_Hypothesis::Hypothesis_Status
   {
     SMESH_subMeshIteratorPtr smIt = getDependsOnIterator(false,false);
     while ( smIt->more() ) {
-      SMESH_Hypothesis::Hypothesis_Status ret2 =
+      SMESH_subMesh* sm = smIt->next();
-        smIt->next()->AlgoStateEngine(event, anHyp);
+      SMESH_Hypothesis::Hypothesis_Status ret2 = sm->AlgoStateEngine(event, anHyp);
       if ( ret2 > ret )
+      {
         ret = ret2;
+        _computeError = sm->_computeError;
+        sm->_computeError.reset();
+        if ( exitOnFatal && SMESH_Hypothesis::IsStatusFatal( ret ))
+          break;
+      }
     }
   }
   return ret;

src/SMESH/SMESH_subMesh.hxx

@@ -218,10 +218,10 @@ public:
     AlgoStateEngine(int event, SMESH_Hypothesis * anHyp);
 
   SMESH_Hypothesis::Hypothesis_Status
-    SubMeshesAlgoStateEngine(int event, SMESH_Hypothesis * anHyp);
+    SubMeshesAlgoStateEngine(int event, SMESH_Hypothesis * anHyp, bool exitOnFatal=false);
 
   algo_state             GetAlgoState() const    { return _algoState; }
-  compute_state          GetComputeState() const { return _computeState; };
+  compute_state          GetComputeState() const { return _computeState; }
   SMESH_ComputeErrorPtr& GetComputeError()       { return _computeError; }
 
   void DumpAlgoState(bool isMain);

src/SMESHDS/SMESHDS_Hypothesis.cxx

@@ -103,3 +103,14 @@ bool SMESHDS_Hypothesis::operator==(const SMESHDS_Hypothesis& other) const
   ((SMESHDS_Hypothesis*)&other)->SaveTo(otherSave);
   return mySave.str() == otherSave.str();
 }
+
+//================================================================================
+/*!
+ * \brief Compare types of hypotheses
+ */
+//================================================================================
+
+bool SMESHDS_Hypothesis::IsSameName( const SMESHDS_Hypothesis& other) const
+{
+  return _name == other._name;
+}

src/SMESHDS/SMESHDS_Hypothesis.hxx

@@ -48,6 +48,7 @@ class SMESHDS_EXPORT SMESHDS_Hypothesis
   virtual std::ostream & SaveTo(std::ostream & save)=0;
   virtual std::istream & LoadFrom(std::istream & load)=0;
 
+  bool IsSameName( const SMESHDS_Hypothesis& other) const;
   virtual bool operator==(const SMESHDS_Hypothesis& other) const;
   bool operator!=(const SMESHDS_Hypothesis& other) const { return !(*this==other); }
 

src/SMESHGUI/SMESHGUI_HypothesesUtils.cxx

@@ -93,19 +93,23 @@ namespace SMESH
 
   void processHypothesisStatus(const int                   theHypStatus,
                                SMESH::SMESH_Hypothesis_ptr theHyp,
-                               const bool theIsAddition)
+                               const bool                  theIsAddition,
+                               const char*                 theError = 0)
   {
     if (theHypStatus > SMESH::HYP_OK) {
       // get Hyp name
       QString aHypName ("NULL Hypothesis");
       if (!CORBA::is_nil(theHyp)) {
         _PTR(SObject) Shyp = SMESH::FindSObject(theHyp);
-        if (Shyp)
+        if (Shyp) {
           // name in study
           aHypName = Shyp->GetName().c_str();
-        else
+        }
+        else {
           // label in xml file
-          aHypName = GetHypothesisData(theHyp->GetName())->Label;
+          CORBA::String_var hypType = theHyp->GetName();
+          aHypName = GetHypothesisData( hypType.in() )->Label;
+        }
       }
 
       // message
@@ -116,12 +120,22 @@ namespace SMESH
       else
         aMsg = (isFatal ? "SMESH_CANT_RM_HYP"  : "SMESH_RM_HYP_WRN");
 
-      aMsg = QObject::tr(aMsg.toLatin1().data()).arg(aHypName) +
+      aMsg = QObject::tr(aMsg.toLatin1().data()).arg(aHypName);
+
+      if ( theError && theError[0] )
+      {
+        aMsg += theError;
+      }
+      else
+      {
         QObject::tr(QString("SMESH_HYP_%1").arg(theHypStatus).toLatin1().data());
 
-      if ( theHypStatus == SMESH::HYP_HIDDEN_ALGO ) // PAL18501
+        if ( theHypStatus == SMESH::HYP_HIDDEN_ALGO ) { // PAL18501
-        aMsg = aMsg.arg( GetHypothesisData(theHyp->GetName())->Dim[0] );
+          CORBA::String_var hypType = theHyp->GetName();
-
+          if ( HypothesisData* hd = GetHypothesisData( hypType.in() ))
+            aMsg = aMsg.arg( hd->Dim[0] );
+        }
+      }
       SUIT_MessageBox::warning(SMESHGUI::desktop(),
                                QObject::tr("SMESH_WRN_WARNING"),
                                aMsg);
@@ -520,7 +534,8 @@ namespace SMESH
       _PTR(SObject) SM = SMESH::FindSObject(aMesh);
       GEOM::GEOM_Object_var aShapeObject = SMESH::GetShapeOnMeshOrSubMesh(SM);
       try {
-        res = aMesh->AddHypothesis(aShapeObject, aHyp);
+        CORBA::String_var error;
+        res = aMesh->AddHypothesis(aShapeObject, aHyp, error.out());
         if (res < SMESH::HYP_UNKNOWN_FATAL) {
           _PTR(SObject) aSH = SMESH::FindSObject(aHyp);
           if (SM && aSH) {
@@ -529,7 +544,7 @@ namespace SMESH
         }
         if (res > SMESH::HYP_OK) {
           wc.suspend();
-          processHypothesisStatus(res, aHyp, true);
+          processHypothesisStatus(res, aHyp, true, error.in() );
           wc.resume();
         }
       }
@@ -554,8 +569,10 @@ namespace SMESH
         SMESH::SMESH_Mesh_var aMesh = aSubMesh->GetFather();
         _PTR(SObject) SsubM = SMESH::FindSObject(aSubMesh);
         GEOM::GEOM_Object_var aShapeObject = SMESH::GetShapeOnMeshOrSubMesh(SsubM);
-        if (!aMesh->_is_nil() && SsubM && !aShapeObject->_is_nil()) {
+        if (!aMesh->_is_nil() && SsubM && !aShapeObject->_is_nil())
-          res = aMesh->AddHypothesis(aShapeObject, aHyp);
+        {
+          CORBA::String_var error;
+          res = aMesh->AddHypothesis( aShapeObject, aHyp, error.out() );
           if (res < SMESH::HYP_UNKNOWN_FATAL)  {
             _PTR(SObject) meshSO = SMESH::FindSObject(aMesh);
             if (meshSO)
@@ -563,7 +580,7 @@ namespace SMESH
           }
           if (res > SMESH::HYP_OK) {
             wc.suspend();
-            processHypothesisStatus(res, aHyp, true);
+            processHypothesisStatus( res, aHyp, true, error.in() );
             wc.resume();
           }
         }

src/SMESHGUI/SMESHGUI_MeshDlg.cxx

@@ -32,16 +32,19 @@
 #include <SUIT_ResourceMgr.h>
 
 // Qt includes
-#include <QVBoxLayout>
-#include <QGridLayout>
-#include <QLabel>
-#include <QTabWidget>
-#include <QGroupBox>
-#include <QToolButton>
 #include <QComboBox>
-#include <QMenu>
 #include <QCursor>
+#include <QGridLayout>
+#include <QGroupBox>
+#include <QLabel>
+#include <QListWidget>
+#include <QMenu>
 #include <QPushButton>
+#include <QTabWidget>
+#include <QToolButton>
+#include <QVBoxLayout>
+
+#include <Standard_Integer.hxx>
 
 #define SPACING 6
 #define MARGIN  11
@@ -65,19 +68,21 @@ SMESHGUI_MeshTab::SMESHGUI_MeshTab( QWidget* theParent )
   SUIT_ResourceMgr* aResMgr = SUIT_Session::session()->resourceMgr();
   QIcon aCreateIcon( aResMgr->loadPixmap( "SMESH", tr( "ICON_HYPO" ) ) );
   QIcon aEditIcon( aResMgr->loadPixmap( "SMESH", tr( "ICON_HYPO_EDIT" ) ) );
+  QIcon aPlusIcon( aResMgr->loadPixmap( "SMESH", tr( "ICON_PLUS" ) ) );
+  QIcon aMinusIcon( aResMgr->loadPixmap( "SMESH", tr( "ICON_MINUS" ) ) );
   
   // Algorifm
   QLabel* anAlgoLbl = new QLabel( tr( "ALGORITHM" ), this );
-  myHyp[ Algo ] = new QComboBox( this );
+  myHypCombo[ Algo ] = new QComboBox( this );
   
   // Hypothesis
   QLabel* aHypLbl = new QLabel( tr( "HYPOTHESIS" ), this );
-  myHyp[ MainHyp ] = new QComboBox( this );
+  myHypCombo[ MainHyp ] = new QComboBox( this );
-  myHyp[ MainHyp ]->setSizePolicy( QSizePolicy::Expanding, QSizePolicy::Fixed );
+  myHypCombo[ MainHyp ]->setSizePolicy( QSizePolicy::Expanding, QSizePolicy::Fixed );
-  myCreateHyp[ MainHyp ] = new QToolButton( this );
+  myCreateHypBtn[ MainHyp ] = new QToolButton( this );
-  myCreateHyp[ MainHyp ]->setIcon( aCreateIcon );
+  myCreateHypBtn[ MainHyp ]->setIcon( aCreateIcon );
-  myEditHyp[ MainHyp ] = new QToolButton( this );
+  myEditHypBtn[ MainHyp ] = new QToolButton( this );
-  myEditHyp[ MainHyp ]->setIcon( aEditIcon );
+  myEditHypBtn[ MainHyp ]->setIcon( aEditIcon );
 
   // Line
   QFrame* aLine = new QFrame( this );
@@ -85,12 +90,20 @@ SMESHGUI_MeshTab::SMESHGUI_MeshTab( QWidget* theParent )
 
   // Add. hypothesis
   QLabel* anAddHypLbl = new QLabel( tr( "ADD_HYPOTHESIS" ), this );
-  myHyp[ AddHyp ] = new QComboBox( this );
+  myHypCombo[ AddHyp ] = new QComboBox( this );
-  myHyp[ AddHyp ]->setSizePolicy( QSizePolicy::Expanding, QSizePolicy::Fixed );
+  myHypCombo[ AddHyp ]->setSizePolicy( QSizePolicy::Expanding, QSizePolicy::Fixed );
-  myCreateHyp[ AddHyp ] = new QToolButton( this );
+  myCreateHypBtn[ AddHyp ] = new QToolButton( this );
-  myCreateHyp[ AddHyp ]->setIcon( aCreateIcon );
+  myCreateHypBtn[ AddHyp ]->setIcon( aCreateIcon );
-  myEditHyp[ AddHyp ] = new QToolButton( this );
+  myEditHypBtn[ AddHyp ] = new QToolButton( this );
-  myEditHyp[ AddHyp ]->setIcon( aEditIcon );
+  myEditHypBtn[ AddHyp ]->setIcon( aEditIcon );
+  myEditHypBtn[ MoreAddHyp ] = new QToolButton( this );
+  myEditHypBtn[ MoreAddHyp ]->setIcon( aEditIcon );
+
+  myAddHypList = new QListWidget( this );
+  myMoreAddHypBtn = new QToolButton( this );
+  myMoreAddHypBtn->setIcon( aPlusIcon );
+  myLessAddHypBtn = new QToolButton( this );
+  myLessAddHypBtn->setIcon( aMinusIcon );
 
   // Fill layout
   QGridLayout* aLay = new QGridLayout( this );
@@ -98,26 +111,35 @@ SMESHGUI_MeshTab::SMESHGUI_MeshTab( QWidget* theParent )
   aLay->setSpacing( SPACING );
 
   aLay->addWidget( anAlgoLbl, 0, 0 );
-  aLay->addWidget( myHyp[ Algo ], 0, 1 );
+  aLay->addWidget( myHypCombo[ Algo ], 0, 1 );
   aLay->addWidget( aHypLbl, 1, 0 );
-  aLay->addWidget( myHyp[ MainHyp ], 1, 1 );
+  aLay->addWidget( myHypCombo[ MainHyp ], 1, 1 );
-  aLay->addWidget( myCreateHyp[ MainHyp ], 1, 2 );
+  aLay->addWidget( myCreateHypBtn[ MainHyp ], 1, 2 );
-  aLay->addWidget( myEditHyp[ MainHyp ], 1, 3 );
+  aLay->addWidget( myEditHypBtn[ MainHyp ], 1, 3 );
   aLay->addWidget( aLine, 2, 0, 1, 4 );
   aLay->addWidget( anAddHypLbl, 3, 0 );
-  aLay->addWidget( myHyp[ AddHyp ], 3, 1 );
+  aLay->addWidget( myHypCombo[ AddHyp ], 3, 1 );
-  aLay->addWidget( myCreateHyp[ AddHyp ], 3, 2 );
+  aLay->addWidget( myCreateHypBtn[ AddHyp ], 3, 2 );
-  aLay->addWidget( myEditHyp[ AddHyp ], 3, 3 );
+  aLay->addWidget( myEditHypBtn[ AddHyp ], 3, 3 );
-  aLay->addItem( new QSpacerItem( 0, 0, QSizePolicy::Fixed, QSizePolicy::Expanding ), 4, 0 );
+  aLay->addWidget( myAddHypList, 4, 1, 2, 1 );
+  aLay->addWidget( myMoreAddHypBtn, 4, 2 );
+  aLay->addWidget( myEditHypBtn[ MoreAddHyp ], 4, 3 );
+  aLay->addWidget( myLessAddHypBtn, 5, 2 );
+  aLay->addItem( new QSpacerItem( 0, 0, QSizePolicy::Fixed, QSizePolicy::Expanding ), 6, 0 );
 
   // Connect signals and slots
   for ( int i = MainHyp; i <= AddHyp; i++ )
   {
-    connect( myCreateHyp[ i ], SIGNAL( clicked() )       ,  SLOT( onCreateHyp() ) );
+    connect( myCreateHypBtn[ i ], SIGNAL( clicked() )       ,  SLOT( onCreateHyp() ) );
-    connect( myEditHyp[ i ]  , SIGNAL( clicked() )       ,  SLOT( onEditHyp() ) );
+    connect( myEditHypBtn[ i ]  , SIGNAL( clicked() )       ,  SLOT( onEditHyp() ) );
-    connect( myHyp[ i ]      , SIGNAL( activated( int ) ),  SLOT( onHyp( int ) ) );
+    connect( myHypCombo[ i ]    , SIGNAL( activated( int ) ),  SLOT( onHyp( int ) ) );
   }
-  connect( myHyp[ Algo ], SIGNAL( activated( int ) ), SLOT( onHyp( int ) ) );
+  connect( myHypCombo[ Algo ], SIGNAL( activated( int ) ), SLOT( onHyp( int ) ) );
+
+  connect( myAddHypList, SIGNAL( currentRowChanged( int ) ), SLOT( onHyp( int ) ) );
+  connect( myEditHypBtn[ MoreAddHyp ], SIGNAL( clicked() ), SLOT( onEditHyp() ) );
+  connect( myMoreAddHypBtn, SIGNAL( clicked() ), SLOT( onMoreAddHyp() ));
+  connect( myLessAddHypBtn, SIGNAL( clicked() ), SLOT( onLessAddHyp() ));
 
   // Initialize controls
 
@@ -135,6 +157,49 @@ SMESHGUI_MeshTab::~SMESHGUI_MeshTab()
 {
 }
 
+//================================================================================
+/*!
+ * \brief Adds an item in a control corresponding to \a type
+ *  \param [in] txt - item text
+ *  \param [in] type - HypType
+ *  \param [in] index - index of item in a list of items
+ */
+//================================================================================
+
+void SMESHGUI_MeshTab::addItem( const QString& txt, const int type, const int index )
+{
+  if ( type <= AddHyp )
+  {
+    myHypCombo[ type ]->addItem( txt, QVariant( index ));
+  }
+  else
+  {
+    QListWidgetItem* item = new QListWidgetItem( txt, myAddHypList );
+    item->setData( Qt::UserRole, QVariant( index ));
+  }
+}
+
+//================================================================================
+/*!
+ * \brief Returns index of hyp of a given type
+ */
+//================================================================================
+
+int SMESHGUI_MeshTab::getCurrentIndex( const int type, const bool curByType ) const
+{
+  if ( type <= AddHyp )
+  {
+    return myHypCombo[ type ]->itemData( myHypCombo[ type ]->currentIndex() ).toInt();
+  }
+  else
+  {
+    int row = curByType ? ( type - AddHyp - 1 ) : myAddHypList->currentRow();
+    if ( QListWidgetItem* item = myAddHypList->item( row ))
+      return item->data( Qt::UserRole ).toInt();
+  }
+  return -1;
+}
+
 //================================================================================
 /*!
  * \brief Sets available hypothesis or algorithms
@@ -146,25 +211,26 @@ SMESHGUI_MeshTab::~SMESHGUI_MeshTab()
 //================================================================================
 void SMESHGUI_MeshTab::setAvailableHyps( const int theId, const QStringList& theHyps )
 {
-  myAvailableHyps[ theId ] = theHyps;
+  myAvailableHypTypes[ theId ] = theHyps;
 
   bool enable = ! theHyps.isEmpty();
   if ( theId == Algo ) // fill list of algos
   {
-    myHyp[ Algo ]->clear();
+    myHypCombo[ Algo ]->clear();
     if ( enable )
     {
-      myHyp[ Algo ]->addItem( tr( "NONE" ) );
+      addItem( tr( "NONE"), Algo, 0 );
-      myHyp[ Algo ]->addItems( theHyps );
+      for ( int i = 0, nbHyp = theHyps.count(); i < nbHyp; ++i )
-      myHyp[ Algo ]->setCurrentIndex( 0 );
+        addItem( theHyps[i], Algo, i+1 );
+      myHypCombo[ Algo ]->setCurrentIndex( 0 );
     }
   }
   else // enable buttons
   {
-    myCreateHyp[ theId ]->setEnabled( enable );
+    myCreateHypBtn[ theId ]->setEnabled( enable );
-    myEditHyp  [ theId ]->setEnabled( false );
+    myEditHypBtn  [ theId ]->setEnabled( false );
   }
-  myHyp[ theId ]->setEnabled( enable );
+  myHypCombo[ theId ]->setEnabled( enable );
 }
 
 //================================================================================
@@ -172,7 +238,7 @@ void SMESHGUI_MeshTab::setAvailableHyps( const int theId, const QStringList& the
  * \brief Sets existing hypothesis
  * \param theId - identifier of hypothesis (main or additional, see HypType enumeration)
  * \param theHyps - list of available hypothesis names
- * \param theDefaultAvlbl - \c true means that the algorithm can with w/o hypothesis
+ * \param theDefaultAvlbl - \c true means that the algorithm can work w/o hypothesis
  *                          with some default parameters
  *
  * Sets existing main or additional hypothesis for this tab
@@ -184,17 +250,25 @@ void SMESHGUI_MeshTab::setExistingHyps( const int          theId,
 {
   if ( theId != Algo )
   {
-    bool enable = ! myAvailableHyps[ theId ].isEmpty();
+    bool enable = ! myAvailableHypTypes[ theId ].isEmpty();
-    myHyp[ theId ]->clear();
+    myHypCombo[ theId ]->clear();
     if ( enable )
     {
       QString none = tr( theDefaultAvlbl ? "DEFAULT" : ( theId == AddHyp ) ? "NONE" : "NONE" );
-      myHyp[ theId ]->addItem( none );
+      addItem( none, theId, 0 );
-      myHyp[ theId ]->addItems( theHyps );
+      for ( int i = 0, nbHyp = theHyps.count(); i < nbHyp; ++i )
-      myHyp[ theId ]->setCurrentIndex( 0 );
+        addItem( theHyps[i], theId, i+1 );
+      myHypCombo[ theId ]->setCurrentIndex( 0 );
+    }
+    myHypCombo  [ theId ]->setEnabled( enable );
+    myEditHypBtn[ theId ]->setEnabled( false );
+    if ( theId == AddHyp )
+    {
+      myAddHypList->clear();
+      myEditHypBtn[ MoreAddHyp ]->setEnabled( false );
+      myMoreAddHypBtn->setEnabled( false );
+      myLessAddHypBtn->setEnabled( false );
     }
-    myHyp    [ theId ]->setEnabled( enable );
-    myEditHyp[ theId ]->setEnabled( false );
   }
 }
 
@@ -210,10 +284,15 @@ void SMESHGUI_MeshTab::setExistingHyps( const int          theId,
 //================================================================================
 void SMESHGUI_MeshTab::addHyp( const int theId, const QString& theHyp )
 {
-  myHyp[ theId ]->addItem( theHyp );
+  int index = myHypCombo[ theId ]->count();
-  myHyp[ theId ]->setCurrentIndex( myHyp[ theId ]->count() - 1 );
+  if ( theId == AddHyp )
-  myEditHyp[ theId ]->setEnabled( true );
+    index += myAddHypList->count();
-  myHyp[ theId ]->setEnabled( true );
+  addItem( theHyp, theId, index );
+  myHypCombo[ theId ]->setCurrentIndex( myHypCombo[ theId ]->count() - 1 );
+  myEditHypBtn[ theId ]->setEnabled( true );
+  myHypCombo[ theId ]->setEnabled( true );
+  if ( theId == AddHyp )
+    myMoreAddHypBtn->setEnabled( true );
 }
 
 //================================================================================
@@ -226,13 +305,13 @@ void SMESHGUI_MeshTab::addHyp( const int theId, const QString& theHyp )
  * Renames hypothesis
  */
 //================================================================================
-void SMESHGUI_MeshTab::renameHyp( const int theId, 
+// void SMESHGUI_MeshTab::renameHyp( const int theId,
-                                  const int theIndex, 
+//                                   const int theIndex,
-                                  const QString& theNewName )
+//                                   const QString& theNewName )
-{
+// {
-  if ( theIndex > 0 && theIndex < myHyp[ theId ]->count() )
+//   if ( theIndex > 0 && theIndex < myHypCombo[ theId ]->count() )
-    myHyp[ theId ]->setItemText( theIndex, theNewName );
+//     myHypCombo[ theId ]->setItemText( theIndex, theNewName );
-}                                  
+// }
 
 //================================================================================
 /*!
@@ -245,11 +324,30 @@ void SMESHGUI_MeshTab::renameHyp( const int theId,
 //================================================================================
 void SMESHGUI_MeshTab::setCurrentHyp( const int theId, const int theIndex )
 {
-  if ( theIndex >= 0 && theIndex < myHyp[ theId ]->count() )
+  if ( theId <= AddHyp )
   {
-    myHyp[ theId ]->setCurrentIndex( theIndex );
+    if ( theIndex >= 0 && theIndex < myHypCombo[ theId ]->count() )
-    if ( myEditHyp[ theId ] )
+    {
-      myEditHyp[ theId ]->setEnabled( theIndex > 0 );
+      myHypCombo[ theId ]->setCurrentIndex( theIndex );
+      if ( myEditHypBtn[ theId ] )
+        myEditHypBtn[ theId ]->setEnabled( theIndex > 0 );
+      if ( theId == AddHyp )
+        myMoreAddHypBtn      ->setEnabled( theIndex > 0 );
+    }
+  }
+  else // more than one additional hyp assigned
+  {
+    // move a hyp from myHypCombo[ AddHyp ] to myAddHypList
+    for ( int i = 1, nb = myHypCombo[ AddHyp ]->count(); i < nb; ++i )
+    {
+      int curIndex = myHypCombo[ AddHyp ]->itemData( i ).toInt();
+      if ( theIndex == curIndex )
+      {
+        addItem( myHypCombo[ AddHyp ]->itemText( i ), theId, theIndex );
+        myHypCombo[ AddHyp ]->removeItem( i );
+        break;
+      }
+    }
   }
 }
 
@@ -260,11 +358,26 @@ void SMESHGUI_MeshTab::setCurrentHyp( const int theId, const int theIndex )
   * \retval int - index of current hypothesis
  * 
  * Gets current hypothesis
+ * Use theId > AddHyp to get more than selected addetional hyps (see nbAddHypTypes()).
  */
 //================================================================================
 int SMESHGUI_MeshTab::currentHyp( const int theId ) const
 {
-  return myHyp[ theId ]->currentIndex();
+  return getCurrentIndex( theId, /*curByType=*/true );
+}
+
+//================================================================================
+/*!
+ * \brief Returns nb of selected supplementary additional hypotheses
+ * 
+ * Access to their indices is via currentHyp( AddHyp + i ) where i is within the
+ * range 0 <= i < this->nbAddHypTypes()
+ */
+//================================================================================
+
+int SMESHGUI_MeshTab::nbAddHypTypes() const
+{
+  return myAddHypList->count();
 }
 
 //================================================================================
@@ -277,12 +390,12 @@ int SMESHGUI_MeshTab::currentHyp( const int theId ) const
 //================================================================================
 void SMESHGUI_MeshTab::onCreateHyp()
 {
-  bool isMainHyp = sender() == myCreateHyp[ MainHyp ];
+  bool isMainHyp = ( sender() == myCreateHypBtn[ MainHyp ]);
 
   QMenu aPopup( this );
   
   QStringList aHypNames = isMainHyp ? 
-    myAvailableHyps[ MainHyp ] : myAvailableHyps[ AddHyp ];
+    myAvailableHypTypes[ MainHyp ] : myAvailableHypTypes[ AddHyp ];
 
   QList<QAction*> actions;
   for ( int i = 0, n = aHypNames.count(); i < n; i++ )
@@ -304,8 +417,12 @@ void SMESHGUI_MeshTab::onCreateHyp()
 void SMESHGUI_MeshTab::onEditHyp()
 {
   const QObject* aSender = sender();
-  int aHypType = aSender == myEditHyp[ MainHyp ] ? MainHyp : AddHyp;
+  int aHypType = MainHyp;
-  emit editHyp( aHypType, myHyp[ aHypType ]->currentIndex() - 1 );  // - 1 because there is NONE on the top
+  for ( ; aHypType <= MoreAddHyp; ++aHypType )
+    if ( aSender == myEditHypBtn[ aHypType ])
+      break;
+  emit editHyp( Min( aHypType, AddHyp ),
+                getCurrentIndex( aHypType ) - 1 );  // - 1 because there is NONE on the top
 }
 
 //================================================================================
@@ -320,11 +437,66 @@ void SMESHGUI_MeshTab::onEditHyp()
 void SMESHGUI_MeshTab::onHyp( int theIndex )
 {
   const QObject* aSender = sender();
-  if ( aSender == myHyp[ Algo ] )
+  if ( aSender == myHypCombo[ Algo ] )
+  {
     emit selectAlgo( theIndex - 1 ); // - 1 because there is NONE on the top
-  else {
+  }
-    int anIndex = aSender == myHyp[ MainHyp ] ? MainHyp : AddHyp;
+  else if ( aSender == myAddHypList )
-    myEditHyp[ anIndex ]->setEnabled( theIndex > 0 );
+  {
+    myEditHypBtn[ MoreAddHyp ]->setEnabled( theIndex >= 0 );
+    myLessAddHypBtn           ->setEnabled( theIndex >= 0 );
+  }
+  else
+  {
+    int type = ( aSender == myHypCombo[ MainHyp ] ? MainHyp : AddHyp );
+    myEditHypBtn[ type ]->setEnabled( theIndex > 0 );
+
+    if ( type == AddHyp )
+      myMoreAddHypBtn   ->setEnabled( theIndex > 0 );
+  }
+}
+
+//================================================================================
+/*!
+ * \brief Adds a current additional hyp to myAddHypList
+ * 
+ * SLOT called when myMoreAddHypBtn ("plus") clicked
+ */
+//================================================================================
+
+void SMESHGUI_MeshTab::onMoreAddHyp()
+{
+  int hypIndex = currentHyp( AddHyp );
+  if ( hypIndex > 0 )
+  {
+    // move a hyp from myHypCombo[ AddHyp ] to myAddHypList
+    int comboIndex = myHypCombo[ AddHyp ]->currentIndex();
+    addItem( myHypCombo[ AddHyp ]->itemText( comboIndex ), MoreAddHyp, hypIndex );
+
+    myHypCombo[ AddHyp ]->removeItem( comboIndex );
+    myHypCombo[ AddHyp ]->setCurrentIndex( 0 );
+
+    myMoreAddHypBtn->setEnabled( false );
+    myEditHypBtn[ AddHyp ]->setEnabled( false );
+  }
+}
+
+//================================================================================
+/*!
+ * \brief Removes a current additional hyp from myAddHypList
+ * 
+ * SLOT called when myLessAddHypBtn ("minus") clicked
+ */
+//================================================================================
+
+void SMESHGUI_MeshTab::onLessAddHyp()
+{
+  if ( QListWidgetItem * item = myAddHypList->currentItem() )
+  {
+    // move a hyp from myAddHypList to myHypCombo[ AddHyp ]
+    int hypIndex = item->data( Qt::UserRole ).toInt();
+    addItem( item->text(), AddHyp, hypIndex );
+    delete item;//myAddHypList->takeItem( myAddHypList->currentRow() );
   }
 }
 
@@ -339,9 +511,9 @@ void SMESHGUI_MeshTab::reset()
 {
   for ( int i = Algo; i <= AddHyp; i++ )
   {
-    myHyp[ i ]->setCurrentIndex( 0 );
+    myHypCombo[ i ]->setCurrentIndex( 0 );
-    if ( myEditHyp[ i ] )
+    if ( myEditHypBtn[ i ] )
-      myEditHyp[ i ]->setEnabled( false );
+      myEditHypBtn[ i ]->setEnabled( false );
   }
 }
 

src/SMESHGUI/SMESHGUI_MeshDlg.h

@@ -38,11 +38,12 @@
 #include <QMap>
 
 class SMESHGUI_MeshTab;
-class QTabWidget;
-class QComboBox;
-class QToolButton;
-class QMenu;
 class QAction;
+class QComboBox;
+class QListWidget;
+class QMenu;
+class QTabWidget;
+class QToolButton;
 
 /*!
  * \brief Dialog for mech creation or editing
@@ -112,7 +113,10 @@ public:
   {
     Algo = 0, //!< algorithms
     MainHyp,  //!< main hypothesis
-    AddHyp    //!< additional hypothesis
+    AddHyp,    //!< additional hypothesis
+    MoreAddHyp //! since several additional hypothesis are possible, the 2-nd, 3-d etc
+    // additional hypotheses are coded as being of HypType (AddHyp + 1), (AddHyp + 2) etc.
+    // Nb of HypType's after MainHyp is returned by SMESHGUI_MeshTab::nbAddHypTypes()
   };
 
 public:      
@@ -122,9 +126,10 @@ public:
   void                         setAvailableHyps( const int, const QStringList& );
   void                         setExistingHyps( const int, const QStringList&, bool=false);
   void                         addHyp( const int, const QString& );
-  void                         renameHyp( const int, const int, const QString& );
+  //void                         renameHyp( const int, const int, const QString& );
   void                         setCurrentHyp( const int, const int );
   int                          currentHyp( const int ) const;
+  int                          nbAddHypTypes() const;
   void                         reset();
 
 signals:  
@@ -139,14 +144,24 @@ private slots:
   void                         onCreateHyp();  
   void                         onEditHyp();
   void                         onHyp( int );
+  void                         onMoreAddHyp();
+  void                         onLessAddHyp();
 
 private:
-  QMap<int, QComboBox*>        myHyp;
-  QMap<int, QToolButton*>      myCreateHyp;
-  QMap<int, QToolButton*>      myEditHyp;
 
-  QMap<int, QStringList>       myAvailableHyps;
+  void                         addItem( const QString& txt, const int type, const int index );
-  QMap<int, QStringList>       myExistingHyps;
+  int                          getCurrentIndex( const int type, const bool curByType=false) const;
+
+  QMap<int, QStringList>       myAvailableHypTypes;
+
+  QMap<int, QComboBox*>        myHypCombo;
+  QMap<int, QToolButton*>      myCreateHypBtn;
+  QMap<int, QToolButton*>      myEditHypBtn;
+
+  QToolButton*                 myMoreAddHypBtn;
+  QToolButton*                 myLessAddHypBtn;
+  QListWidget*                 myAddHypList; // 2-nd, etc. additional hyps
+
 };
 
 #endif // SMESHGUI_MESHDLG_H

src/SMESHGUI/SMESHGUI_MeshOp.cxx

@@ -610,8 +610,8 @@ void SMESHGUI_MeshOp::selectionDone()
           myDlg->objectWg( SMESHGUI_MeshDlg::Geom, SMESHGUI_MeshDlg::Btn )->hide();
           myDlg->updateGeometry();
           myDlg->adjustSize();
-          readMesh();
           myIsMesh = submeshVar->_is_nil();
+          readMesh();
         }
         else
           myDlg->reset();
@@ -873,7 +873,11 @@ void SMESHGUI_MeshOp::availableHyps( const int       theDim,
  *  \param theAlgoData - to select hypos able to be used by this algo (optional)
  *
  * Gets existing (i.e. already created) hypotheses or algorithm in accordance with
- * input parameters
+ * input parameters.
+ *
+ * WARNING: when using this method to get hyps existing in Mesh component,
+ *          call availableHyps() before in order to get only hyps of available types
+ *          that was filtered by availableHyps()
  */
 //================================================================================
 void SMESHGUI_MeshOp::existingHyps( const int       theDim,
@@ -881,7 +885,7 @@ void SMESHGUI_MeshOp::existingHyps( const int       theDim,
                                     _PTR(SObject)   theFather,
                                     QStringList&    theHyps,
                                     THypList&       theHypList,
-                                    HypothesisData* theAlgoData)
+                                    HypothesisData* theAlgoData) const
 {
   // Clear hypoheses list
   theHyps.clear();
@@ -890,20 +894,21 @@ void SMESHGUI_MeshOp::existingHyps( const int       theDim,
   if ( !theFather )
     return;
 
-  const bool isAux  = ( theHypType == AddHyp );
-
   _PTR(SObject)          aHypRoot;
   _PTR(GenericAttribute) anAttr;
   _PTR(AttributeName)    aName;
   _PTR(AttributeIOR)     anIOR;
 
-  bool isMesh = !_CAST( SComponent, theFather );
+  const bool isMesh = !_CAST( SComponent, theFather );
   int aPart = -1;
   if ( isMesh )
     aPart = theHypType == Algo ? SMESH::Tag_RefOnAppliedAlgorithms : SMESH::Tag_RefOnAppliedHypothesis;
   else
     aPart = theHypType == Algo ? SMESH::Tag_AlgorithmsRoot : SMESH::Tag_HypothesisRoot;
 
+  const bool isAux   = ( theHypType == AddHyp );
+  const bool allHyps = ( !isMesh && theHypType != Algo && theDim > -1);
+
   if ( theFather->FindSubObject( aPart, aHypRoot ) )
   {
     _PTR(ChildIterator) anIter =
@@ -933,7 +938,8 @@ void SMESHGUI_MeshOp::existingHyps( const int       theDim,
             if ( !aData) continue;
             if (( theDim == -1 || aData->Dim.contains( theDim ) ) &&
                 ( isCompatible ( theAlgoData, aData, theHypType )) &&
-                 ( theHypType == Algo || isAux == aData->IsAuxOrNeedHyp ))
+                ( theHypType == Algo || isAux == aData->IsAuxOrNeedHyp ) &&
+                ( !allHyps || myAvailableHypData[theDim][theHypType].count(aData) ))
             {
               std::string aHypName = aName->Value();
               theHyps.append( aHypName.c_str() );
@@ -1173,6 +1179,8 @@ void SMESHGUI_MeshOp::createHypothesis(const int theDim,
 
   myDim = theDim;
   myType = theType;
+
+  // get a unique hyp name
   QStringList aHypNames;
   TDim2Type2HypList::const_iterator aDimIter = myExistingHyps.begin();
   for ( ; aDimIter != myExistingHyps.end(); aDimIter++) {
@@ -1481,13 +1489,14 @@ void SMESHGUI_MeshOp::onAlgoSelected( const int theIndex,
   {
     if ( !isAccessibleDim( dim ))
       continue;
-    for ( int type = MainHyp; type < NbHypTypes; type++ )
+    for ( int dlgType = MainHyp; dlgType < nbDlgHypTypes(dim); dlgType++ )
     {
+      const int type = Min( dlgType, AddHyp );
       myAvailableHypData[ dim ][ type ].clear();
       QStringList anAvailable, anExisting;
 
       HypothesisData* curAlgo = algoByDim[ dim ];
-      int hypIndex = currentHyp( dim, type );
+      int hypIndex = currentHyp( dim, dlgType );
 
       SMESH::SMESH_Hypothesis_var curHyp;
       if ( hypIndex >= 0 && hypIndex < myExistingHyps[ dim ][ type ].count() )
@@ -1521,8 +1530,8 @@ void SMESHGUI_MeshOp::onAlgoSelected( const int theIndex,
           if ( !isCompatible( curAlgo, hypData, type ))
             curHyp = SMESH::SMESH_Hypothesis::_nil();
         }
-        existingHyps( dim, type, pObj, anExisting, myExistingHyps[ dim ][ type ], curAlgo);
         availableHyps( dim, type, anAvailable, myAvailableHypData[ dim ][ type ], curAlgo);
+        existingHyps( dim, type, pObj, anExisting, myExistingHyps[ dim ][ type ], curAlgo);
         defaulHypAvlbl = (type == MainHyp && !curAlgo->IsAuxOrNeedHyp );
       }
       // set list of hypotheses
@@ -1701,14 +1710,19 @@ bool SMESHGUI_MeshOp::createMesh( QString& theMess, QStringList& theEntryList )
       SMESH::SetName( aMeshSO, myDlg->objectText( SMESHGUI_MeshDlg::Obj ) );
     }
 
-    for ( int aDim = SMESH::DIM_0D; aDim <= SMESH::DIM_3D; aDim++ ) {
+    for ( int aDim = SMESH::DIM_0D; aDim <= SMESH::DIM_3D; aDim++ )
+    {
       if ( !isAccessibleDim( aDim )) continue;
 
       // assign hypotheses
-      for ( int aHypType = MainHyp; aHypType <= AddHyp; aHypType++ ) {
+      for ( int dlgType = MainHyp; dlgType < nbDlgHypTypes(aDim); dlgType++ )
-        int aHypIndex = currentHyp( aDim, aHypType );
+      {
-        if ( aHypIndex >= 0 && aHypIndex < myExistingHyps[ aDim ][ aHypType ].count() ) {
+        const int aHypIndex = currentHyp( aDim, dlgType );
-          SMESH::SMESH_Hypothesis_var aHypVar = myExistingHyps[ aDim ][ aHypType ][ aHypIndex ].first;
+        const int  aHypType = Min( dlgType, AddHyp );
+        if ( aHypIndex >= 0 && aHypIndex < myExistingHyps[ aDim ][ aHypType ].count() )
+        {
+          SMESH::SMESH_Hypothesis_var aHypVar =
+            myExistingHyps[ aDim ][ aHypType ][ aHypIndex ].first;
           if ( !aHypVar->_is_nil() )
             SMESH::AddHypothesisOnMesh( aMeshVar, aHypVar );
         }
@@ -1838,9 +1852,10 @@ bool SMESHGUI_MeshOp::createSubMesh( QString& theMess, QStringList& theEntryList
     if ( !anAlgoVar->_is_nil() )
       SMESH::AddHypothesisOnSubMesh( aSubMeshVar, anAlgoVar );
     // assign hypotheses
-    for ( int aHypType = MainHyp; aHypType <= AddHyp; aHypType++ )
+    for ( int dlgType = MainHyp; dlgType < nbDlgHypTypes(aDim); dlgType++ )
     {
-      int aHypIndex = currentHyp( aDim, aHypType );
+      const int aHypIndex = currentHyp( aDim, dlgType );
+      const int  aHypType = Min( dlgType, AddHyp );
       if ( aHypIndex >= 0 && aHypIndex < myExistingHyps[ aDim ][ aHypType ].count() )
       {
         SMESH::SMESH_Hypothesis_var aHypVar =
@@ -1876,6 +1891,36 @@ int SMESHGUI_MeshOp::currentHyp( const int theDim, const int theHypType ) const
   return myDlg->tab( theDim )->currentHyp( theHypType ) - 1;
 }
 
+//================================================================================
+/*!
+ * \brief Checks if a hypothesis is selected
+ */
+//================================================================================
+
+bool SMESHGUI_MeshOp::isSelectedHyp( int theDim, int theHypType, int theIndex) const
+{
+  if ( theHypType < AddHyp ) // only one hyp can be selected
+    return currentHyp( theDim, theHypType ) == theIndex;
+
+  for ( int dlgHypType = AddHyp; dlgHypType < nbDlgHypTypes( theDim ); ++dlgHypType )
+    if ( currentHyp( theDim, dlgHypType ) == theIndex )
+      return true;
+
+  return false;
+}
+
+//================================================================================
+/*!
+ * \brief Returns nb of HypType's taking into account possible several
+ *        selected additional hypotheses which are coded as additional HypType's.
+ */
+//================================================================================
+
+int SMESHGUI_MeshOp::nbDlgHypTypes( const int dim ) const
+{
+  return NbHypTypes + myDlg->tab( dim )->nbAddHypTypes();
+}
+
 //================================================================================
 /*!
  * \brief Returns true if hypotheses of given dim can be assigned
@@ -2095,23 +2140,26 @@ void SMESHGUI_MeshOp::readMesh()
     {
       // get hypotheses
       existingHyps( dim, hypType, pObj, anExisting, myObjHyps[ dim ][ hypType ] );
-      // find index of requered hypothesis among existing ones for this dimension and type
+      for ( int i = 0, nb = myObjHyps[ dim ][ hypType ].count(); i < nb; ++i )
-      int aHypIndex = -1;
+      {
-      if ( myObjHyps[ dim ][ hypType ].count() > 0 ) {
+        // find index of required hypothesis among existing ones for this dimension and type
-        aHypIndex = find( myObjHyps[ dim ][ hypType ].first().first,
+        int aHypIndex = find( myObjHyps[ dim ][ hypType ][ i ].first,
                               myExistingHyps[ dim ][ hypType ] );
         if ( aHypIndex < 0 ) {
           // assigned hypothesis is incompatible with the algorithm
           if ( currentHyp( dim, Algo ) < 0 )
           { // none algo selected; it is edition for sure, of submesh maybe
             hypWithoutAlgo = true;
-            myExistingHyps[ dim ][ hypType ].push_back( myObjHyps[ dim ][ hypType ].first() );
+            myExistingHyps[ dim ][ hypType ].push_back( myObjHyps[ dim ][ hypType ][ i ] );
+            anExisting.push_back( myObjHyps[ dim ][ hypType ][ i ].second );
             aHypIndex = myExistingHyps[ dim ][ hypType ].count() - 1;
             myDlg->tab( dim )->setExistingHyps( hypType, anExisting );
           }
         }
+        setCurrentHyp( dim, hypType + i, aHypIndex );
+
+        if ( hypType == MainHyp ) break; // only one main hyp allowed
       }
-      setCurrentHyp( dim, hypType, aHypIndex );
     }
   }
   // make available other hyps of same type as one without algo
@@ -2249,37 +2297,38 @@ bool SMESHGUI_MeshOp::editMeshOrSubMesh( QString& theMess )
       myObjHyps[ dim ][ Algo ].append( THypItem( anAlgoVar, aName) );
     }
 
-    // assign hypotheses
+    // remove deselected hypotheses
     for ( int hypType = MainHyp; hypType <= AddHyp; hypType++ )
     {
-      int aNewHypIndex = currentHyp( dim, hypType );
+      for ( int i = 0, nb = myObjHyps[ dim ][ hypType ].count(); i < nb; ++i )
-      int anOldHypIndex = -1;
-
-      // remove old hypotheses
-      if ( myObjHyps[ dim ][ hypType ].count() > 0 )
       {
-        anOldHypIndex = find( myObjHyps[ dim ][ hypType ].first().first,
+        SMESH::SMESH_Hypothesis_var hyp = myObjHyps[ dim ][ hypType ][ i ].first;
-                              myExistingHyps[ dim ][ hypType ] );
+        int hypIndex = this->find( hyp, myExistingHyps[ dim ][ hypType ]);
-        if ( aNewHypIndex != anOldHypIndex || // different hyps
+        if ( !isSelectedHyp( dim, hypType, hypIndex ) && !hyp->_is_nil() )
-             anOldHypIndex == -1 )            // hyps of different algos
         {
-          SMESH::RemoveHypothesisOrAlgorithmOnMesh
+          SMESH::RemoveHypothesisOrAlgorithmOnMesh( pObj, hyp );
-            ( pObj, myObjHyps[ dim ][ hypType ].first().first );
-          myObjHyps[ dim ][ hypType ].clear();
         }
       }
+    }
+    // assign newly selected hypotheses
+    for ( int dlgType = MainHyp; dlgType < nbDlgHypTypes(dim); dlgType++ )
+    {
+      const int curIndex = currentHyp( dim, dlgType );
+      const int  hypType = Min( dlgType, AddHyp );
+      if ( curIndex >= 0 && curIndex < myExistingHyps[ dim ][ hypType ].count() )
+      {
+        SMESH::SMESH_Hypothesis_var hyp = myExistingHyps[ dim ][ hypType ][ curIndex ].first;
 
-      // assign new hypotheses
+        bool isAssigned = ( this->find( hyp, myObjHyps[ dim ][ hypType ]) >= 0 );
-      if ( aNewHypIndex != anOldHypIndex && aNewHypIndex > -1 )
+        if ( !isAssigned )
         {
           if ( isMesh )
-          SMESH::AddHypothesisOnMesh
+            SMESH::AddHypothesisOnMesh (aMeshVar, hyp );
-            (aMeshVar, myExistingHyps[ dim ][ hypType ][ aNewHypIndex ].first );
           else if ( !aSubMeshVar->_is_nil() )
-          SMESH::AddHypothesisOnSubMesh
+            SMESH::AddHypothesisOnSubMesh ( aSubMeshVar, hyp );
-            ( aSubMeshVar, myExistingHyps[ dim ][ hypType ][ aNewHypIndex ].first );
         }
-      // reread all hypotheses of mesh if necessary
+      }
+      // reread all hypotheses of mesh
       QStringList anExisting;
       existingHyps( dim, hypType, pObj, anExisting, myObjHyps[ dim ][ hypType ] );
     }

src/SMESHGUI/SMESHGUI_MeshOp.h

@@ -96,12 +96,12 @@ private:
                                                 QStringList&,
                                                 THypDataList&,
                                                 HypothesisData* = 0 ) const;
-  static void                    existingHyps( const int, 
+  void                           existingHyps( const int, 
                                                const int, 
                                                _PTR(SObject),
                                                QStringList&, 
                                                THypList&,
-                                               HypothesisData* = 0 );
+                                               HypothesisData* = 0 ) const;
   HypothesisData*                hypData( const int,
                                           const int,
                                           const int ); // access to myAvailableHypData
@@ -117,6 +117,8 @@ private:
                                                           bool                     askUser=false);
 
   int                            currentHyp( const int, const int ) const;
+  bool                           isSelectedHyp( int, int, int ) const;
+  int                            nbDlgHypTypes( const int ) const;
   bool                           isAccessibleDim( const int ) const;
   void                           setCurrentHyp( const int, const int, const int );
   void                           setDefaultName( const QString& prefix="" ) const;
@@ -135,7 +137,9 @@ private:
   void                           createMeshTypeList( QStringList& );
   void                           setAvailableMeshType( const QStringList& );
   void                           setFilteredAlgoData( const int, const int );
+
 private:
+
   SMESHGUI_MeshDlg*              myDlg;
   SMESHGUI_ShapeByMeshOp*        myShapeByMeshOp;
   bool                           myToCreate;

src/SMESHGUI/SMESH_images.ts

@@ -299,6 +299,14 @@
             <source>ICON_HYPO_EDIT</source>
             <translation>mesh_hypo_edit.png</translation>
         </message>
+        <message>
+            <source>ICON_PLUS</source>
+            <translation>mesh_plus.png</translation>
+        </message>
+        <message>
+            <source>ICON_MINUS</source>
+            <translation>mesh_minus.png</translation>
+        </message>
         <message>
             <source>ICON_INTERSECT</source>
             <translation>mesh_intersectGroups.png</translation>

src/SMESH_I/SMESH_Mesh_i.cxx

@@ -549,6 +549,7 @@ SMESH::Hypothesis_Status SMESH_Mesh_i::ConvertHypothesisStatus
   RETURNCASE( HYP_BAD_SUBSHAPE  );
   RETURNCASE( HYP_BAD_GEOMETRY  );
   RETURNCASE( HYP_NEED_SHAPE    );
+  RETURNCASE( HYP_INCOMPAT_HYPS );
   default:;
   }
   return SMESH::HYP_UNKNOWN_FATAL;
@@ -564,33 +565,31 @@ SMESH::Hypothesis_Status SMESH_Mesh_i::ConvertHypothesisStatus
  */
 //=============================================================================
 
-SMESH::Hypothesis_Status SMESH_Mesh_i::AddHypothesis(GEOM::GEOM_Object_ptr       aSubShapeObject,
+SMESH::Hypothesis_Status
-                                                     SMESH::SMESH_Hypothesis_ptr anHyp)
+SMESH_Mesh_i::AddHypothesis(GEOM::GEOM_Object_ptr       aSubShape,
+                            SMESH::SMESH_Hypothesis_ptr anHyp,
+                            CORBA::String_out           anErrorText)
   throw(SALOME::SALOME_Exception)
 {
   Unexpect aCatch(SALOME_SalomeException);
   if ( _preMeshInfo )
     _preMeshInfo->ForgetOrLoad();
 
-  SMESH_Hypothesis::Hypothesis_Status status = addHypothesis( aSubShapeObject, anHyp );
+  std::string error;
+  SMESH_Hypothesis::Hypothesis_Status status = addHypothesis( aSubShape, anHyp, &error );
+  anErrorText = error.c_str();
 
   SMESH::SMESH_Mesh_var mesh( _this() );
   if ( !SMESH_Hypothesis::IsStatusFatal(status) )
   {
     SALOMEDS::Study_var study = _gen_i->GetCurrentStudy();
-    _gen_i->AddHypothesisToShape( study, mesh, aSubShapeObject, anHyp );
+    _gen_i->AddHypothesisToShape( study, mesh, aSubShape, anHyp );
   }
   if(MYDEBUG) MESSAGE( " AddHypothesis(): status = " << status );
 
   // Update Python script
-  //if(_impl->HasShapeToMesh())
-  {
   TPythonDump() << "status = " << mesh << ".AddHypothesis( "
-                  << aSubShapeObject << ", " << anHyp << " )";
+                << aSubShape << ", " << anHyp << " )";
-  }
-  // else {
-  //   TPythonDump() << "status = " << mesh << ".AddHypothesis( "<< anHyp << " )";
-  // }
 
   return ConvertHypothesisStatus(status);
 }
@@ -602,12 +601,13 @@ SMESH::Hypothesis_Status SMESH_Mesh_i::AddHypothesis(GEOM::GEOM_Object_ptr
 //=============================================================================
 
 SMESH_Hypothesis::Hypothesis_Status
-SMESH_Mesh_i::addHypothesis(GEOM::GEOM_Object_ptr       aSubShapeObject,
+SMESH_Mesh_i::addHypothesis(GEOM::GEOM_Object_ptr       aSubShape,
-                            SMESH::SMESH_Hypothesis_ptr anHyp)
+                            SMESH::SMESH_Hypothesis_ptr anHyp,
+                            std::string*                anErrorText)
 {
   if(MYDEBUG) MESSAGE("addHypothesis");
 
-  if (CORBA::is_nil( aSubShapeObject ) && HasShapeToMesh())
+  if (CORBA::is_nil( aSubShape ) && HasShapeToMesh())
     THROW_SALOME_CORBA_EXCEPTION("bad Sub-shape reference",SALOME::BAD_PARAM);
 
   if (CORBA::is_nil( anHyp ))
@@ -619,22 +619,28 @@ SMESH_Mesh_i::addHypothesis(GEOM::GEOM_Object_ptr       aSubShapeObject,
     TopoDS_Shape myLocSubShape;
     //use PseudoShape in case if mesh has no shape
     if(HasShapeToMesh())
-      myLocSubShape = _gen_i->GeomObjectToShape( aSubShapeObject);
+      myLocSubShape = _gen_i->GeomObjectToShape( aSubShape);
     else              
       myLocSubShape = _impl->GetShapeToMesh();
     
     const int hypId = anHyp->GetId();
-    status = _impl->AddHypothesis(myLocSubShape, hypId);
+    std::string error;
-    if ( !SMESH_Hypothesis::IsStatusFatal(status) ) {
+    status = _impl->AddHypothesis( myLocSubShape, hypId, &error );
+    if ( !SMESH_Hypothesis::IsStatusFatal(status) )
+    {
       _mapHypo[hypId] = SMESH::SMESH_Hypothesis::_duplicate( anHyp );
       anHyp->Register();
       // assure there is a corresponding submesh
       if ( !_impl->IsMainShape( myLocSubShape )) {
         int shapeId = _impl->GetMeshDS()->ShapeToIndex( myLocSubShape );
         if ( _mapSubMesh_i.find( shapeId ) == _mapSubMesh_i.end() )
-          SMESH::SMESH_subMesh_var( createSubMesh( aSubShapeObject ));
+          SMESH::SMESH_subMesh_var( createSubMesh( aSubShape ));
       }
     }
+    else if ( anErrorText )
+    {
+      *anErrorText = error;
+    }
   }
   catch(SALOME_Exception & S_ex)
   {
@@ -649,7 +655,7 @@ SMESH_Mesh_i::addHypothesis(GEOM::GEOM_Object_ptr       aSubShapeObject,
  */
 //=============================================================================
 
-SMESH::Hypothesis_Status SMESH_Mesh_i::RemoveHypothesis(GEOM::GEOM_Object_ptr aSubShapeObject,
+SMESH::Hypothesis_Status SMESH_Mesh_i::RemoveHypothesis(GEOM::GEOM_Object_ptr aSubShape,
                                                         SMESH::SMESH_Hypothesis_ptr anHyp)
   throw(SALOME::SALOME_Exception)
 {
@@ -657,18 +663,18 @@ SMESH::Hypothesis_Status SMESH_Mesh_i::RemoveHypothesis(GEOM::GEOM_Object_ptr aS
   if ( _preMeshInfo )
     _preMeshInfo->ForgetOrLoad();
 
-  SMESH_Hypothesis::Hypothesis_Status status = removeHypothesis( aSubShapeObject, anHyp );
+  SMESH_Hypothesis::Hypothesis_Status status = removeHypothesis( aSubShape, anHyp );
   SMESH::SMESH_Mesh_var mesh = _this();
 
   if ( !SMESH_Hypothesis::IsStatusFatal(status) )
   {
     SALOMEDS::Study_var study = _gen_i->GetCurrentStudy();
-    _gen_i->RemoveHypothesisFromShape( study, mesh, aSubShapeObject, anHyp );
+    _gen_i->RemoveHypothesisFromShape( study, mesh, aSubShape, anHyp );
   }
   // Update Python script
   if(_impl->HasShapeToMesh())
     TPythonDump() << "status = " << mesh << ".RemoveHypothesis( "
-                  << aSubShapeObject << ", " << anHyp << " )";
+                  << aSubShape << ", " << anHyp << " )";
   else
     TPythonDump() << "status = " << mesh << ".RemoveHypothesis( "
                   << anHyp << " )";
@@ -683,12 +689,12 @@ SMESH::Hypothesis_Status SMESH_Mesh_i::RemoveHypothesis(GEOM::GEOM_Object_ptr aS
 //=============================================================================
 
 SMESH_Hypothesis::Hypothesis_Status
-SMESH_Mesh_i::removeHypothesis(GEOM::GEOM_Object_ptr       aSubShapeObject,
+SMESH_Mesh_i::removeHypothesis(GEOM::GEOM_Object_ptr       aSubShape,
                                SMESH::SMESH_Hypothesis_ptr anHyp)
 {
   if(MYDEBUG) MESSAGE("removeHypothesis()");
 
-  if (CORBA::is_nil( aSubShapeObject ) && HasShapeToMesh())
+  if (CORBA::is_nil( aSubShape ) && HasShapeToMesh())
     THROW_SALOME_CORBA_EXCEPTION("bad Sub-shape reference", SALOME::BAD_PARAM);
 
   if (CORBA::is_nil( anHyp ))
@@ -700,7 +706,7 @@ SMESH_Mesh_i::removeHypothesis(GEOM::GEOM_Object_ptr       aSubShapeObject,
     TopoDS_Shape myLocSubShape;
     //use PseudoShape in case if mesh has no shape
     if( _impl->HasShapeToMesh() )
-      myLocSubShape = _gen_i->GeomObjectToShape( aSubShapeObject );
+      myLocSubShape = _gen_i->GeomObjectToShape( aSubShape );
     else
       myLocSubShape = _impl->GetShapeToMesh();
 
@@ -726,18 +732,18 @@ SMESH_Mesh_i::removeHypothesis(GEOM::GEOM_Object_ptr       aSubShapeObject,
 //=============================================================================
 
 SMESH::ListOfHypothesis *
-SMESH_Mesh_i::GetHypothesisList(GEOM::GEOM_Object_ptr aSubShapeObject)
+SMESH_Mesh_i::GetHypothesisList(GEOM::GEOM_Object_ptr aSubShape)
 throw(SALOME::SALOME_Exception)
 {
   Unexpect aCatch(SALOME_SalomeException);
   if (MYDEBUG) MESSAGE("GetHypothesisList");
-  if (_impl->HasShapeToMesh() && CORBA::is_nil(aSubShapeObject))
+  if (_impl->HasShapeToMesh() && CORBA::is_nil(aSubShape))
     THROW_SALOME_CORBA_EXCEPTION("bad Sub-shape reference", SALOME::BAD_PARAM);
 
   SMESH::ListOfHypothesis_var aList = new SMESH::ListOfHypothesis();
 
   try {
-    TopoDS_Shape myLocSubShape = _gen_i->GeomObjectToShape(aSubShapeObject);
+    TopoDS_Shape myLocSubShape = _gen_i->GeomObjectToShape(aSubShape);
     if ( myLocSubShape.IsNull() && !_impl->HasShapeToMesh() )
       myLocSubShape = _impl->GetShapeToMesh();
     const list<const SMESHDS_Hypothesis*>& aLocalList = _impl->GetHypothesisList( myLocSubShape );
@@ -803,18 +809,18 @@ SMESH::submesh_array* SMESH_Mesh_i::GetSubMeshes() throw (SALOME::SALOME_Excepti
  */
 //=============================================================================
 
-SMESH::SMESH_subMesh_ptr SMESH_Mesh_i::GetSubMesh(GEOM::GEOM_Object_ptr aSubShapeObject,
+SMESH::SMESH_subMesh_ptr SMESH_Mesh_i::GetSubMesh(GEOM::GEOM_Object_ptr aSubShape,
                                                   const char*           theName )
      throw(SALOME::SALOME_Exception)
 {
   Unexpect aCatch(SALOME_SalomeException);
-  if (CORBA::is_nil(aSubShapeObject))
+  if (CORBA::is_nil(aSubShape))
     THROW_SALOME_CORBA_EXCEPTION("bad Sub-shape reference", SALOME::BAD_PARAM);
 
   SMESH::SMESH_subMesh_var subMesh;
   SMESH::SMESH_Mesh_var    aMesh = _this();
   try {
-    TopoDS_Shape myLocSubShape = _gen_i->GeomObjectToShape(aSubShapeObject);
+    TopoDS_Shape myLocSubShape = _gen_i->GeomObjectToShape(aSubShape);
 
     //Get or Create the SMESH_subMesh object implementation
 
@@ -830,16 +836,16 @@ SMESH::SMESH_subMesh_ptr SMESH_Mesh_i::GetSubMesh(GEOM::GEOM_Object_ptr aSubShap
 
     // create a new subMesh object servant if there is none for the shape
     if ( subMesh->_is_nil() )
-      subMesh = createSubMesh( aSubShapeObject );
+      subMesh = createSubMesh( aSubShape );
     if ( _gen_i->CanPublishInStudy( subMesh ))
     {
       SALOMEDS::Study_var study = _gen_i->GetCurrentStudy();
       SALOMEDS::SObject_wrap aSO =
-        _gen_i->PublishSubMesh( study, aMesh, subMesh, aSubShapeObject, theName );
+        _gen_i->PublishSubMesh( study, aMesh, subMesh, aSubShape, theName );
       if ( !aSO->_is_nil()) {
         // Update Python script
         TPythonDump() << aSO << " = " << aMesh << ".GetSubMesh( "
-                      << aSubShapeObject << ", '" << theName << "' )";
+                      << aSubShape << ", '" << theName << "' )";
       }
     }
   }
@@ -863,7 +869,7 @@ void SMESH_Mesh_i::RemoveSubMesh( SMESH::SMESH_subMesh_ptr theSubMesh )
   if ( theSubMesh->_is_nil() )
     return;
 
-  GEOM::GEOM_Object_var aSubShapeObject;
+  GEOM::GEOM_Object_var aSubShape;
   SALOMEDS::Study_var aStudy = _gen_i->GetCurrentStudy();
   if ( !aStudy->_is_nil() )  {
     // Remove submesh's SObject
@@ -875,10 +881,10 @@ void SMESH_Mesh_i::RemoveSubMesh( SMESH::SMESH_subMesh_ptr theSubMesh )
            anObj->ReferencedObject( aRef.inout() ))
       {
         CORBA::Object_var obj = aRef->GetObject();
-        aSubShapeObject = GEOM::GEOM_Object::_narrow( obj );
+        aSubShape = GEOM::GEOM_Object::_narrow( obj );
       }
-      // if ( aSubShapeObject->_is_nil() ) // not published shape (IPAL13617)
+      // if ( aSubShape->_is_nil() ) // not published shape (IPAL13617)
-      //   aSubShapeObject = theSubMesh->GetSubShape();
+      //   aSubShape = theSubMesh->GetSubShape();
 
       SALOMEDS::StudyBuilder_var builder = aStudy->NewBuilder();
       builder->RemoveObjectWithChildren( anSO );
@@ -888,7 +894,7 @@ void SMESH_Mesh_i::RemoveSubMesh( SMESH::SMESH_subMesh_ptr theSubMesh )
     }
   }
 
-  if ( removeSubMesh( theSubMesh, aSubShapeObject.in() ))
+  if ( removeSubMesh( theSubMesh, aSubShape.in() ))
     if ( _preMeshInfo )
       _preMeshInfo->ForgetOrLoad();
 

src/SMESH_I/SMESH_Mesh_i.hxx

@@ -86,21 +86,22 @@ public:
   void ClearSubMesh(CORBA::Long ShapeID)
     throw (SALOME::SALOME_Exception);
 
-  SMESH::Hypothesis_Status AddHypothesis(GEOM::GEOM_Object_ptr aSubShapeObject,
+  SMESH::Hypothesis_Status AddHypothesis(GEOM::GEOM_Object_ptr       aSubShape,
+                                         SMESH::SMESH_Hypothesis_ptr anHyp,
+                                         CORBA::String_out           anErrorText)
+    throw (SALOME::SALOME_Exception);
+
+  SMESH::Hypothesis_Status RemoveHypothesis(GEOM::GEOM_Object_ptr       aSubShape,
                                             SMESH::SMESH_Hypothesis_ptr anHyp)
     throw (SALOME::SALOME_Exception);
 
-  SMESH::Hypothesis_Status RemoveHypothesis(GEOM::GEOM_Object_ptr aSubShapeObject,
+  SMESH::ListOfHypothesis* GetHypothesisList(GEOM::GEOM_Object_ptr aSubShape)
-                                            SMESH::SMESH_Hypothesis_ptr anHyp)
-    throw (SALOME::SALOME_Exception);
-
-  SMESH::ListOfHypothesis* GetHypothesisList(GEOM::GEOM_Object_ptr aSubShapeObject)
     throw (SALOME::SALOME_Exception);
 
   SMESH::submesh_array* GetSubMeshes()
     throw (SALOME::SALOME_Exception);
 
-  SMESH::SMESH_subMesh_ptr GetSubMesh(GEOM::GEOM_Object_ptr aSubShapeObject, const char* theName)
+  SMESH::SMESH_subMesh_ptr GetSubMesh(GEOM::GEOM_Object_ptr aSubShape, const char* theName)
     throw (SALOME::SALOME_Exception);
 
   void RemoveSubMesh( SMESH::SMESH_subMesh_ptr theSubMesh )
@@ -404,10 +405,11 @@ public:
 
   // Internal methods not available through CORBA
   // They are called by corresponding interface methods
-  SMESH_Hypothesis::Hypothesis_Status addHypothesis(GEOM::GEOM_Object_ptr aSubShapeObject,
+  SMESH_Hypothesis::Hypothesis_Status addHypothesis(GEOM::GEOM_Object_ptr       aSubShape,
-                                                    SMESH::SMESH_Hypothesis_ptr anHyp);
+                                                    SMESH::SMESH_Hypothesis_ptr anHyp,
+                                                    std::string*                anErrorText=0);
 
-  SMESH_Hypothesis::Hypothesis_Status removeHypothesis(GEOM::GEOM_Object_ptr aSubShapeObject,
+  SMESH_Hypothesis::Hypothesis_Status removeHypothesis(GEOM::GEOM_Object_ptr aSubShape,
                                                        SMESH::SMESH_Hypothesis_ptr anHyp);
 
   static SMESH::Hypothesis_Status

src/SMESH_SWIG/smeshBuilder.py

@@ -207,12 +207,15 @@ def GetName(obj):
     raise RuntimeError, "Null or invalid object"
 
 ## Prints error message if a hypothesis was not assigned.
-def TreatHypoStatus(status, hypName, geomName, isAlgo):
+def TreatHypoStatus(status, hypName, geomName, isAlgo, mesh):
     if isAlgo:
         hypType = "algorithm"
     else:
         hypType = "hypothesis"
         pass
+    reason = ""
+    if hasattr( status, "__getitem__" ):
+        status,reason = status[0],status[1]
     if status == HYP_UNKNOWN_FATAL :
         reason = "for unknown reason"
     elif status == HYP_INCOMPATIBLE :
@@ -235,17 +238,24 @@ def TreatHypoStatus(status, hypName, geomName, isAlgo):
     elif status == HYP_HIDING_ALGO:
         reason = "it hides algorithms of lower dimensions by generating elements of all dimensions"
     elif status == HYP_NEED_SHAPE:
-        reason = "Algorithm can't work without shape"
+        reason = "algorithm can't work without shape"
+    elif status == HYP_INCOMPAT_HYPS:
+        pass
     else:
         return
-    hypName = '"' + hypName + '"'
+    where = geomName
-    geomName= '"' + geomName+ '"'
+    if where:
-    if status < HYP_UNKNOWN_FATAL and not geomName =='""':
+        where = '"%s"' % geomName
-        print hypName, "was assigned to",    geomName,"but", reason
+        if mesh:
-    elif not geomName == '""':
+            meshName = GetName( mesh )
-        print hypName, "was not assigned to",geomName,":", reason
+            if meshName and meshName != NO_NAME:
+                where = '"%s" in "%s"' % ( geomName, meshName )
+    if status < HYP_UNKNOWN_FATAL and where:
+        print '"%s" was assigned to %s but %s' %( hypName, where, reason )
+    elif where:
+        print '"%s" was not assigned to %s : %s' %( hypName, where, reason )
     else:
-        print hypName, "was not assigned:", reason
+        print '"%s" was not assigned : %s' %( hypName, reason )
         pass
 
 ## Private method. Add geom (sub-shape of the main shape) into the study if not yet there
@@ -1592,7 +1602,7 @@ class Mesh:
         if geom:
             geom_name = geom.GetName()
         isAlgo = hyp._narrow( SMESH_Algo )
-        TreatHypoStatus( status, hyp_name, geom_name, isAlgo )
+        TreatHypoStatus( status, hyp_name, geom_name, isAlgo, self )
         return status
 
     ## Return True if an algorithm of hypothesis is assigned to a given shape
@@ -1878,7 +1888,7 @@ class Mesh:
     #  @param UnaryOp FT_LogicalNOT or FT_Undefined
     #  @param Tolerance the tolerance used by FT_BelongToGeom, FT_BelongToSurface,
     #         FT_LyingOnGeom, FT_CoplanarFaces criteria
-    #  @return SMESH_Group
+    #  @return SMESH_GroupOnFilter
     #  @ingroup l2_grps_create
     def MakeGroup(self,
                   groupName,
@@ -1895,7 +1905,7 @@ class Mesh:
     ## Creates a mesh group by the given criterion
     #  @param groupName the name of the mesh group
     #  @param Criterion the instance of Criterion class
-    #  @return SMESH_Group
+    #  @return SMESH_GroupOnFilter
     #  @ingroup l2_grps_create
     def MakeGroupByCriterion(self, groupName, Criterion):
         aFilterMgr = self.smeshpyD.CreateFilterManager()
@@ -1910,7 +1920,7 @@ class Mesh:
     ## Creates a mesh group by the given criteria (list of criteria)
     #  @param groupName the name of the mesh group
     #  @param theCriteria the list of criteria
-    #  @return SMESH_Group
+    #  @return SMESH_GroupOnFilter
     #  @ingroup l2_grps_create
     def MakeGroupByCriteria(self, groupName, theCriteria):
         aFilterMgr = self.smeshpyD.CreateFilterManager()
@@ -1923,12 +1933,13 @@ class Mesh:
     ## Creates a mesh group by the given filter
     #  @param groupName the name of the mesh group
     #  @param theFilter the instance of Filter class
-    #  @return SMESH_Group
+    #  @return SMESH_GroupOnFilter
     #  @ingroup l2_grps_create
     def MakeGroupByFilter(self, groupName, theFilter):
-        group = self.CreateEmptyGroup(theFilter.GetElementType(), groupName)
+        #group = self.CreateEmptyGroup(theFilter.GetElementType(), groupName)
-        theFilter.SetMesh( self.mesh )
+        #theFilter.SetMesh( self.mesh )
-        group.AddFrom( theFilter )
+        #group.AddFrom( theFilter )
+        group = self.GroupOnFilter( theFilter.GetElementType(), groupName, theFilter )
         return group
 
     ## Removes a group

src/SMESH_SWIG/smesh_algorithm.py

@@ -214,7 +214,7 @@ class Mesh_Algorithm:
 
     ## Private method
     def Hypothesis (self, hyp, args=[], so="libStdMeshersEngine.so",
-                    UseExisting=0, CompareMethod=""):
+                    UseExisting=0, CompareMethod="", toAdd=True):
         from salome.smesh.smeshBuilder import TreatHypoStatus, GetName
         hypo = None
         if UseExisting:
@@ -243,8 +243,9 @@ class Mesh_Algorithm:
         geomName=""
         if self.geom:
             geomName = GetName(self.geom)
+        if toAdd:
             status = self.mesh.mesh.AddHypothesis(self.geom, hypo)
-        TreatHypoStatus( status, GetName(hypo), geomName, 0 )
+            TreatHypoStatus( status, GetName(hypo), geomName, 0, self.mesh )
         return hypo
 
     ## Returns entry of the shape to mesh in the study
@@ -275,11 +276,13 @@ class Mesh_Algorithm:
         if faces and isinstance( faces[0], geomBuilder.GEOM._objref_GEOM_Object ):
             faces = [ self.mesh.geompyD.GetSubShapeID(self.mesh.geom, f) for f in faces ]
         hyp = self.Hypothesis("ViscousLayers",
-                              [thickness, numberOfLayers, stretchFactor, faces])
+                              [thickness, numberOfLayers, stretchFactor, faces, isFacesToIgnore],
+                              toAdd=False)
         hyp.SetTotalThickness(thickness)
         hyp.SetNumberLayers(numberOfLayers)
         hyp.SetStretchFactor(stretchFactor)
         hyp.SetFaces(faces, isFacesToIgnore)
+        self.mesh.AddHypothesis( hyp, self.geom )
         return hyp
 
     ## Defines "ViscousLayers2D" hypothesis to give parameters of layers of quadrilateral
@@ -303,12 +306,13 @@ class Mesh_Algorithm:
         if edges and isinstance( edges[0], geomBuilder.GEOM._objref_GEOM_Object ):
             edges = [ self.mesh.geompyD.GetSubShapeID(self.mesh.geom, f) for f in edges ]
         hyp = self.Hypothesis("ViscousLayers2D",
-                              [thickness, numberOfLayers, stretchFactor,
+                              [thickness, numberOfLayers, stretchFactor, edges, isEdgesToIgnore],
-                               edges, isEdgesToIgnore])
+                              toAdd=False)
         hyp.SetTotalThickness(thickness)
         hyp.SetNumberLayers(numberOfLayers)
         hyp.SetStretchFactor(stretchFactor)
         hyp.SetEdges(edges, isEdgesToIgnore)
+        self.mesh.AddHypothesis( hyp, self.geom )
         return hyp
 
     ## Transform a list of either edges or tuples (edge, 1st_vertex_of_edge)

src/StdMeshers/StdMeshers_FaceSide.cxx

@@ -1012,7 +1012,8 @@ TSideVector StdMeshers_FaceSide::GetFaceWires(const TopoDS_Face&   theFace,
                                               SMESH_Mesh &         theMesh,
                                               const bool           theIgnoreMediumNodes,
                                               TError &             theError,
-                                              SMESH_ProxyMesh::Ptr theProxyMesh)
+                                              SMESH_ProxyMesh::Ptr theProxyMesh,
+                                              const bool           theCheckVertexNodes)
 {
   list< TopoDS_Edge > edges, internalEdges;
   list< int > nbEdgesInWires;
@@ -1037,6 +1038,7 @@ TSideVector StdMeshers_FaceSide::GetFaceWires(const TopoDS_Face&   theFace,
     // as StdMeshers_FaceSide::GetUVPtStruct() requires
     if ( wireEdges.front().Orientation() != TopAbs_INTERNAL ) // Issue 0020676
     {
+      if ( theCheckVertexNodes )
         while ( !SMESH_Algo::VertexNode( TopExp::FirstVertex( wireEdges.front(), true),
                                          theMesh.GetMeshDS()))
         {

src/StdMeshers/StdMeshers_FaceSide.hxx

@@ -141,7 +141,8 @@ public:
                                   SMESH_Mesh &         theMesh,
                                   const bool           theIgnoreMediumNodes,
                                   TError &             theError,
-                                  SMESH_ProxyMesh::Ptr theProxyMesh = SMESH_ProxyMesh::Ptr());
+                                  SMESH_ProxyMesh::Ptr theProxyMesh = SMESH_ProxyMesh::Ptr(),
+                                  const bool           theCheckVertexNodes=true);
   /*!
    * \brief Change orientation of side geometry
    */

src/StdMeshers/StdMeshers_Hexa_3D.cxx

@@ -124,23 +124,17 @@ bool StdMeshers_Hexa_3D::CheckHypothesis
     return true;
   }
 
+  // only StdMeshers_ViscousLayers can be used
   aStatus = HYP_OK;
   for ( ; h != hyps.end(); ++h )
   {
-    string hypName = (*h)->GetName();
+    if ( !(_viscousLayersHyp = dynamic_cast< const StdMeshers_ViscousLayers*> ( *h )))
-    if ( find( _compatibleHypothesis.begin(),_compatibleHypothesis.end(),hypName )
+      break;
-         != _compatibleHypothesis.end() )
-    {
-      _viscousLayersHyp = dynamic_cast< const StdMeshers_ViscousLayers*> ( *h );
   }
-    else
-    {
-      aStatus = HYP_INCOMPATIBLE;
-    }
-  }
-
   if ( !_viscousLayersHyp )
     aStatus = HYP_INCOMPATIBLE;
+  else
+    error( _viscousLayersHyp->CheckHypothesis( aMesh, aShape, aStatus ));
 
   return aStatus == HYP_OK;
 }

src/StdMeshers/StdMeshers_MEFISTO_2D.cxx

@@ -122,6 +122,9 @@ bool StdMeshers_MEFISTO_2D::CheckHypothesis
   _edgeLength = 0;
   _maxElementArea = 0;
 
+  if ( !error( StdMeshers_ViscousLayers2D::CheckHypothesis( aMesh, aShape, aStatus )))
+    return false;
+
   list <const SMESHDS_Hypothesis * >::const_iterator itl;
   const SMESHDS_Hypothesis *theHyp;
 

src/StdMeshers/StdMeshers_Propagation.cxx

@@ -114,7 +114,17 @@ TopoDS_Edge StdMeshers_Propagation::GetPropagationSource(SMESH_Mesh&         the
   return PropagationMgr::GetSource( theMesh.GetSubMeshContaining( theEdge ),
                                     isPropagOfDistribution);
 }
-
+const SMESH_HypoFilter& StdMeshers_Propagation::GetFilter()
+{
+  static SMESH_HypoFilter propagHypFilter;
+  if ( propagHypFilter.IsEmpty() )
+  {
+    propagHypFilter.
+      Init( SMESH_HypoFilter::HasName( StdMeshers_Propagation::GetName ())).
+      Or  ( SMESH_HypoFilter::HasName( StdMeshers_PropagOfDistribution::GetName ()));
+  }
+  return propagHypFilter;
+}
 //=============================================================================
 //=============================================================================
 // PROPAGATION MANAGEMENT
@@ -226,14 +236,8 @@ namespace {
    */
   const SMESH_Hypothesis* getProagationHyp (SMESH_subMesh* theSubMesh)
   {
-    static SMESH_HypoFilter propagHypFilter;
+    return theSubMesh->GetFather()->GetHypothesis
-    if ( propagHypFilter.IsEmpty() )
+      ( theSubMesh, StdMeshers_Propagation::GetFilter(), true );
-    {
-      propagHypFilter.
-        Init( SMESH_HypoFilter::HasName( StdMeshers_Propagation::GetName ())).
-        Or  ( SMESH_HypoFilter::HasName( StdMeshers_PropagOfDistribution::GetName ()));
-    }
-    return theSubMesh->GetFather()->GetHypothesis( theSubMesh, propagHypFilter, true );
   }
   //================================================================================
   /*!

src/StdMeshers/StdMeshers_Propagation.hxx

@@ -35,6 +35,7 @@
 
 #include <TopoDS_Edge.hxx>
 
+class SMESH_HypoFilter;
 
 // =======================================================================
 /*!
@@ -53,6 +54,12 @@ class STDMESHERS_EXPORT StdMeshers_Propagation:public SMESH_Hypothesis
 
   static std::string GetName ();
 
+  /*!
+   * \brief Returns a filter selecting both StdMeshers_Propagation and
+   *        StdMeshers_PropagOfDistribution hypotheses
+   */
+  static const SMESH_HypoFilter& GetFilter();
+
   /*!
    * \brief Set EventListener managing propagation of hypotheses
     * \param subMesh - edge submesh to set event listener on

src/StdMeshers/StdMeshers_Quadrangle_2D.cxx

@@ -199,7 +199,9 @@ bool StdMeshers_Quadrangle_2D::CheckHypothesis
     }
   }
 
-  return isOk;
+  error( StdMeshers_ViscousLayers2D::CheckHypothesis( aMesh, aShape, aStatus ));
+
+  return aStatus == HYP_OK;
 }
 
 //=============================================================================

src/StdMeshers/StdMeshers_Regular_1D.cxx

@@ -127,13 +127,18 @@ bool StdMeshers_Regular_1D::CheckHypothesis( SMESH_Mesh&         aMesh,
   const list <const SMESHDS_Hypothesis * > & hyps =
     GetUsedHypothesis(aMesh, aShape, /*ignoreAuxiliaryHyps=*/false);
 
+  const SMESH_HypoFilter & propagFilter = StdMeshers_Propagation::GetFilter();
+
   // find non-auxiliary hypothesis
   const SMESHDS_Hypothesis *theHyp = 0;
+  set< string > propagTypes;
   list <const SMESHDS_Hypothesis * >::const_iterator h = hyps.begin();
   for ( ; h != hyps.end(); ++h ) {
     if ( static_cast<const SMESH_Hypothesis*>(*h)->IsAuxiliary() ) {
       if ( strcmp( "QuadraticMesh", (*h)->GetName() ) == 0 )
         _quadraticMesh = true;
+      if ( propagFilter.IsOk( static_cast< const SMESH_Hypothesis*>( *h ), aShape ))
+        propagTypes.insert( (*h)->GetName() );
     }
     else {
       if ( !theHyp )
@@ -293,11 +298,48 @@ bool StdMeshers_Regular_1D::CheckHypothesis( SMESH_Mesh&         aMesh,
     ASSERT(_adaptiveHyp);
     _hypType = ADAPTIVE;
     _onlyUnaryInput = false;
+    aStatus = SMESH_Hypothesis::HYP_OK;
   }
   else
+  {
     aStatus = SMESH_Hypothesis::HYP_INCOMPATIBLE;
+  }
 
-  return ( _hypType != NONE );
+  if ( propagTypes.size() > 1 && aStatus == HYP_OK )
+  {
+    // detect concurrent Propagation hyps
+    _usedHypList.clear();
+    list< TopoDS_Shape > assignedTo;
+    if ( aMesh.GetHypotheses( aShape, propagFilter, _usedHypList, true, &assignedTo ) > 1 )
+    {
+      // find most simple shape and a hyp on it
+      int simpleShape = TopAbs_COMPOUND;
+      const SMESHDS_Hypothesis* localHyp = 0;
+      list< TopoDS_Shape >::iterator            shape = assignedTo.begin();
+      list< const SMESHDS_Hypothesis *>::iterator hyp = _usedHypList.begin();
+      for ( ; shape != assignedTo.end(); ++shape )
+        if ( shape->ShapeType() > simpleShape )
+        {
+          simpleShape = shape->ShapeType();
+          localHyp = (*hyp);
+        }
+      // check if there a different hyp on simpleShape
+      shape = assignedTo.begin();
+      hyp = _usedHypList.begin();
+      for ( ; hyp != _usedHypList.end(); ++hyp, ++shape )
+        if ( shape->ShapeType() == simpleShape &&
+             !localHyp->IsSameName( **hyp ))
+        {
+          aStatus = HYP_INCOMPAT_HYPS;
+          return error( SMESH_Comment("Hypotheses of both \"")
+                        << StdMeshers_Propagation::GetName() << "\" and \""
+                        << StdMeshers_PropagOfDistribution::GetName()
+                        << "\" types can't be applied to the same edge");
+        }
+    }
+  }
+
+  return ( aStatus == SMESH_Hypothesis::HYP_OK );
 }
 
 static bool computeParamByFunc(Adaptor3d_Curve& C3d, double first, double last,

src/StdMeshers/StdMeshers_ViscousLayers.cxx

@@ -355,6 +355,7 @@ namespace VISCOUS_3D
     bool   IsOnEdge() const { return _2neibors; }
     gp_XYZ Copy( _LayerEdge& other, SMESH_MesherHelper& helper );
     void   SetCosin( double cosin );
+    int    NbSteps() const { return _pos.size() - 1; } // nb inlation steps
   };
   struct _LayerEdgeCmp
   {
@@ -414,6 +415,36 @@ namespace VISCOUS_3D
     bool CheckPrisms() const;
   };
 
+  //--------------------------------------------------------------------------------
+  /*!
+   * \brief Layers parameters got by averaging several hypotheses
+   */
+  struct AverageHyp
+  {
+    AverageHyp( const StdMeshers_ViscousLayers* hyp = 0 )
+      :_nbLayers(0), _nbHyps(0), _thickness(0), _stretchFactor(0)
+    {
+      Add( hyp );
+    }
+    void Add( const StdMeshers_ViscousLayers* hyp )
+    {
+      if ( hyp )
+      {
+        _nbHyps++;
+        _nbLayers       = hyp->GetNumberLayers();
+        //_thickness     += hyp->GetTotalThickness();
+        _thickness     = Max( _thickness, hyp->GetTotalThickness() );
+        _stretchFactor += hyp->GetStretchFactor();
+      }
+    }
+    double GetTotalThickness() const { return _thickness; /*_nbHyps ? _thickness / _nbHyps : 0;*/ }
+    double GetStretchFactor()  const { return _nbHyps ? _stretchFactor / _nbHyps : 0; }
+    int    GetNumberLayers()   const { return _nbLayers; }
+  private:
+    int     _nbLayers, _nbHyps;
+    double  _thickness, _stretchFactor;
+  };
+
   //--------------------------------------------------------------------------------
 
   typedef map< const SMDS_MeshNode*, _LayerEdge*, TIDCompare > TNode2Edge;
@@ -424,12 +455,15 @@ namespace VISCOUS_3D
    */
   struct _SolidData
   {
+    typedef const StdMeshers_ViscousLayers* THyp;
     TopoDS_Shape                    _solid;
-    const StdMeshers_ViscousLayers* _hyp;
+    TGeomID                         _index; // SOLID id
-    TopoDS_Shape                    _hypShape;
     _MeshOfSolid*                   _proxyMesh;
+    list< THyp >                    _hyps;
+    list< TopoDS_Shape >            _hypShapes;
+    map< TGeomID, THyp >            _face2hyp; // filled if _hyps.size() > 1
     set< TGeomID >                  _reversedFaceIds;
-    set<TGeomID>                    _ignoreFaceIds; // WOL FACEs and FACEs of other SOLIDS
+    set< TGeomID >                  _ignoreFaceIds; // WOL FACEs and FACEs of other SOLIDs
 
     double                          _stepSize, _stepSizeCoeff, _geomSize;
     const SMDS_MeshNode*            _stepSizeNodes[2];
@@ -439,7 +473,7 @@ namespace VISCOUS_3D
     // map to find _n2eMap of another _SolidData by a shrink shape shared by two _SolidData's
     map< TGeomID, TNode2Edge* >     _s2neMap;
     // edges of _n2eMap. We keep same data in two containers because
-    // iteration over the map is 5 time longer than over the vector
+    // iteration over the map is 5 times longer than over the vector
     vector< _LayerEdge* >           _edges;
 
     // key:   an id of shape (EDGE or VERTEX) shared by a FACE with
@@ -462,15 +496,16 @@ namespace VISCOUS_3D
     vector< int >                    _endEdgeOnShape;
     int                              _nbShapesToSmooth;
 
+    // data of averaged StdMeshers_ViscousLayers parameters for each shape with _LayerEdge's
+    vector< AverageHyp >             _hypOnShape;
+    double                           _maxThickness; // of all _hyps
+    double                           _minThickness; // of all _hyps
+
     double                           _epsilon; // precision for SegTriaInter()
 
-    TGeomID                          _index; // SOLID id, for debug
-
     _SolidData(const TopoDS_Shape& s=TopoDS_Shape(),
-               const StdMeshers_ViscousLayers* h=0,
-               const TopoDS_Shape&             hs=TopoDS_Shape(),
                _MeshOfSolid*       m=0)
-      :_solid(s), _hyp(h), _hypShape(hs), _proxyMesh(m) {}
+      :_solid(s), _proxyMesh(m) {}
     ~_SolidData();
 
     Handle(Geom_Curve) CurveForSmooth( const TopoDS_Edge&    E,
@@ -496,7 +531,7 @@ namespace VISCOUS_3D
       iEnd = _endEdgeOnShape[ end ];
     }
 
-    bool GetShapeEdges(const TGeomID shapeID, size_t& edgeEnd, int* iBeg=0, int* iEnd=0 ) const;
+    bool GetShapeEdges(const TGeomID shapeID, size_t& iEdgeEnd, int* iBeg=0, int* iEnd=0 ) const;
 
     void AddShapesToSmooth( const set< TGeomID >& shapeIDs );
   };
@@ -563,6 +598,9 @@ namespace VISCOUS_3D
     // does it's job
     SMESH_ComputeErrorPtr Compute(SMESH_Mesh&         mesh,
                                   const TopoDS_Shape& shape);
+    // check validity of hypotheses
+    SMESH_ComputeErrorPtr CheckHypotheses( SMESH_Mesh&         mesh,
+                                           const TopoDS_Shape& shape );
 
     // restore event listeners used to clear an inferior dim sub-mesh modified by viscous layers
     void RestoreListeners();
@@ -573,7 +611,11 @@ namespace VISCOUS_3D
   private:
 
     bool findSolidsWithLayers();
-    bool findFacesWithLayers();
+    bool findFacesWithLayers(const bool onlyWith=false);
+    void getIgnoreFaces(const TopoDS_Shape&             solid,
+                        const StdMeshers_ViscousLayers* hyp,
+                        const TopoDS_Shape&             hypShape,
+                        set<TGeomID>&                   ignoreFaces);
     bool makeLayer(_SolidData& data);
     bool setEdgeData(_LayerEdge& edge, const set<TGeomID>& subIds,
                      SMESH_MesherHelper& helper, _SolidData& data);
@@ -832,6 +874,27 @@ bool StdMeshers_ViscousLayers::SetParametersByMesh(const SMESH_Mesh*   theMesh,
 {
   // TODO
   return false;
+} // --------------------------------------------------------------------------------
+SMESH_ComputeErrorPtr
+StdMeshers_ViscousLayers::CheckHypothesis(SMESH_Mesh&                          theMesh,
+                                          const TopoDS_Shape&                  theShape,
+                                          SMESH_Hypothesis::Hypothesis_Status& theStatus)
+{
+  VISCOUS_3D::_ViscousBuilder bulder;
+  SMESH_ComputeErrorPtr err = bulder.CheckHypotheses( theMesh, theShape );
+  if ( err && !err->IsOK() )
+    theStatus = SMESH_Hypothesis::HYP_INCOMPAT_HYPS;
+  else
+    theStatus = SMESH_Hypothesis::HYP_OK;
+
+  return err;
+}
+// --------------------------------------------------------------------------------
+bool StdMeshers_ViscousLayers::IsShapeWithLayers(int shapeIndex) const
+{
+  bool isIn =
+    ( std::find( _shapeIds.begin(), _shapeIds.end(), shapeIndex ) != _shapeIds.end() );
+  return IsToIgnoreShapes() ? !isIn : isIn;
 }
 // END StdMeshers_ViscousLayers hypothesis
 //================================================================================
@@ -1313,6 +1376,34 @@ SMESH_ComputeErrorPtr _ViscousBuilder::Compute(SMESH_Mesh&         theMesh,
   return _error;
 }
 
+//================================================================================
+/*!
+ * \brief Check validity of hypotheses
+ */
+//================================================================================
+
+SMESH_ComputeErrorPtr _ViscousBuilder::CheckHypotheses( SMESH_Mesh&         mesh,
+                                                        const TopoDS_Shape& shape )
+{
+  _mesh = & mesh;
+
+  if ( _ViscousListener::GetSolidMesh( _mesh, shape, /*toCreate=*/false))
+    return SMESH_ComputeErrorPtr(); // everything already computed
+
+
+  findSolidsWithLayers();
+  bool ok = findFacesWithLayers();
+
+  // remove _MeshOfSolid's of _SolidData's
+  for ( size_t i = 0; i < _sdVec.size(); ++i )
+    _ViscousListener::RemoveSolidMesh( _mesh, _sdVec[i]._solid );
+
+  if ( !ok )
+    return _error;
+
+  return SMESH_ComputeErrorPtr();
+}
+
 //================================================================================
 /*!
  * \brief Finds SOLIDs to compute using viscous layers. Fills _sdVec
@@ -1336,21 +1427,27 @@ bool _ViscousBuilder::findSolidsWithLayers()
     // TODO: check if algo is hidden
     const list <const SMESHDS_Hypothesis *> & allHyps =
       algo->GetUsedHypothesis(*_mesh, allSolids(i), /*ignoreAuxiliary=*/false);
+    _SolidData* soData = 0;
     list< const SMESHDS_Hypothesis *>::const_iterator hyp = allHyps.begin();
     const StdMeshers_ViscousLayers* viscHyp = 0;
-    for ( ; hyp != allHyps.end() && !viscHyp; ++hyp )
+    for ( ; hyp != allHyps.end(); ++hyp )
-      viscHyp = dynamic_cast<const StdMeshers_ViscousLayers*>( *hyp );
+      if ( viscHyp = dynamic_cast<const StdMeshers_ViscousLayers*>( *hyp ))
-    if ( viscHyp )
       {
         TopoDS_Shape hypShape;
         filter.Init( filter.Is( viscHyp ));
         _mesh->GetHypothesis( allSolids(i), filter, true, &hypShape );
 
+        if ( !soData )
+        {
           _MeshOfSolid* proxyMesh = _ViscousListener::GetSolidMesh( _mesh,
                                                                     allSolids(i),
                                                                     /*toCreate=*/true);
-      _sdVec.push_back( _SolidData( allSolids(i), viscHyp, hypShape, proxyMesh ));
+          _sdVec.push_back( _SolidData( allSolids(i), proxyMesh ));
-      _sdVec.back()._index = getMeshDS()->ShapeToIndex( allSolids(i));
+          soData = & _sdVec.back();
+          soData->_index = getMeshDS()->ShapeToIndex( allSolids(i));
+        }
+        soData->_hyps.push_back( viscHyp );
+        soData->_hypShapes.push_back( hypShape );
       }
   }
   if ( _sdVec.empty() )
@@ -1366,7 +1463,7 @@ bool _ViscousBuilder::findSolidsWithLayers()
  */
 //================================================================================
 
-bool _ViscousBuilder::findFacesWithLayers()
+bool _ViscousBuilder::findFacesWithLayers(const bool onlyWith)
 {
   SMESH_MesherHelper helper( *_mesh );
   TopExp_Explorer exp;
@@ -1377,56 +1474,99 @@ bool _ViscousBuilder::findFacesWithLayers()
   {
     solids.Add( _sdVec[i]._solid );
 
-    vector<TGeomID> ids = _sdVec[i]._hyp->GetBndShapes();
+    // get faces to ignore defined by each hyp
-    if ( _sdVec[i]._hyp->IsToIgnoreShapes() ) // FACEs to ignore are given
+    typedef const StdMeshers_ViscousLayers* THyp;
+    typedef std::pair< set<TGeomID>, THyp > TFacesOfHyp;
+    list< TFacesOfHyp > ignoreFacesOfHyps;
+    list< THyp >::iterator              hyp = _sdVec[i]._hyps.begin();
+    list< TopoDS_Shape >::iterator hypShape = _sdVec[i]._hypShapes.begin();
+    for ( ; hyp != _sdVec[i]._hyps.end(); ++hyp, ++hypShape )
     {
-      for ( size_t ii = 0; ii < ids.size(); ++ii )
+      ignoreFacesOfHyps.push_back( TFacesOfHyp( set<TGeomID>(), *hyp ));
-      {
+      getIgnoreFaces( _sdVec[i]._solid, *hyp, *hypShape, ignoreFacesOfHyps.back().first );
-        const TopoDS_Shape& s = getMeshDS()->IndexToShape( ids[ii] );
-        if ( !s.IsNull() && s.ShapeType() == TopAbs_FACE )
-          _sdVec[i]._ignoreFaceIds.insert( ids[ii] );
-      }
-    }
-    else // FACEs with layers are given
-    {
-      exp.Init( _sdVec[i]._solid, TopAbs_FACE );
-      for ( ; exp.More(); exp.Next() )
-      {
-        TGeomID faceInd = getMeshDS()->ShapeToIndex( exp.Current() );
-        if ( find( ids.begin(), ids.end(), faceInd ) == ids.end() )
-          _sdVec[i]._ignoreFaceIds.insert( faceInd );
-      }
     }
 
-    // ignore internal FACEs if inlets and outlets are specified
+    // fill _SolidData::_face2hyp and check compatibility of hypotheses
+    const int nbHyps = _sdVec[i]._hyps.size();
+    if ( nbHyps > 1 )
     {
-      TopTools_IndexedDataMapOfShapeListOfShape solidsOfFace;
+      // check if two hypotheses define different parameters for the same FACE
-      if ( _sdVec[i]._hyp->IsToIgnoreShapes() )
+      list< TFacesOfHyp >::iterator igFacesOfHyp;
-        TopExp::MapShapesAndAncestors( _sdVec[i]._hypShape,
+      for ( exp.Init( _sdVec[i]._solid, TopAbs_FACE ); exp.More(); exp.Next() )
-                                       TopAbs_FACE, TopAbs_SOLID, solidsOfFace);
+      {
+        const TGeomID faceID = getMeshDS()->ShapeToIndex( exp.Current() );
+        THyp hyp = 0;
+        igFacesOfHyp = ignoreFacesOfHyps.begin();
+        for ( ; igFacesOfHyp != ignoreFacesOfHyps.end(); ++igFacesOfHyp )
+          if ( ! igFacesOfHyp->first.count( faceID ))
+          {
+            if ( hyp )
+              return error(SMESH_Comment("Several hypotheses define "
+                                         "Viscous Layers on the face #") << faceID );
+            hyp = igFacesOfHyp->second;
+          }
+        if ( hyp )
+          _sdVec[i]._face2hyp.insert( make_pair( faceID, hyp ));
+        else
+          _sdVec[i]._ignoreFaceIds.insert( faceID );
+      }
 
+      // check if two hypotheses define different number of viscous layers for
+      // adjacent faces of a solid
+      set< int > nbLayersSet;
+      igFacesOfHyp = ignoreFacesOfHyps.begin();
+      for ( ; igFacesOfHyp != ignoreFacesOfHyps.end(); ++igFacesOfHyp )
+      {
+        nbLayersSet.insert( igFacesOfHyp->second->GetNumberLayers() );
+      }
+      if ( nbLayersSet.size() > 1 )
+      {
+        for ( exp.Init( _sdVec[i]._solid, TopAbs_EDGE ); exp.More(); exp.Next() )
+        {
+          PShapeIteratorPtr fIt = helper.GetAncestors( exp.Current(), *_mesh, TopAbs_FACE );
+          THyp hyp1 = 0, hyp2 = 0;
+          while( const TopoDS_Shape* face = fIt->next() )
+          {
+            const TGeomID faceID = getMeshDS()->ShapeToIndex( *face );
+            map< TGeomID, THyp >::iterator f2h = _sdVec[i]._face2hyp.find( faceID );
+            if ( f2h != _sdVec[i]._face2hyp.end() )
+            {
+              ( hyp1 ? hyp2 : hyp1 ) = f2h->second;
+            }
+          }
+          if ( hyp1 && hyp2 &&
+               hyp1->GetNumberLayers() != hyp2->GetNumberLayers() )
+          {
+            return error("Two hypotheses define different number of "
+                         "viscous layers on adjacent faces");
+          }
+        }
+      }
+    } // if ( nbHyps > 1 )
+    else
+    {
+      _sdVec[i]._ignoreFaceIds.swap( ignoreFacesOfHyps.back().first );
+    }
+
+    // fill _SolidData::_reversedFaceIds
+    {
       exp.Init( _sdVec[i]._solid.Oriented( TopAbs_FORWARD ), TopAbs_FACE );
       for ( ; exp.More(); exp.Next() )
       {
         const TopoDS_Face& face = TopoDS::Face( exp.Current() );
-        if ( helper.NbAncestors( face, *_mesh, TopAbs_SOLID ) < 2 )
+        const TGeomID faceID = getMeshDS()->ShapeToIndex( face );
-          continue;
+        if ( //!sdVec[i]._ignoreFaceIds.count( faceID ) && ???????
-
+             helper.NbAncestors( face, *_mesh, TopAbs_SOLID ) > 1 &&
-        const TGeomID faceInd = getMeshDS()->ShapeToIndex( face );
+             helper.IsReversedSubMesh( face ))
-        if ( _sdVec[i]._hyp->IsToIgnoreShapes() )
         {
-          int nbSolids = solidsOfFace.FindFromKey( face ).Extent();
+          _sdVec[i]._reversedFaceIds.insert( faceID );
-          if ( nbSolids > 1 )
-            _sdVec[i]._ignoreFaceIds.insert( faceInd );
         }
+      }
+    }
+  } // loop on _sdVec
 
-        if ( helper.IsReversedSubMesh( face ))
+  if ( onlyWith ) // is called to check hypotheses compatibility only
-        {
+    return true;
-          _sdVec[i]._reversedFaceIds.insert( faceInd );
-        }
-      }
-    }
-  }
 
   // Find faces to shrink mesh on (solution 2 in issue 0020832);
   TopTools_IndexedMapOfShape shapes;
@@ -1642,6 +1782,60 @@ bool _ViscousBuilder::findFacesWithLayers()
   return true;
 }
 
+//================================================================================
+/*!
+ * \brief Finds FACEs w/o layers for a given SOLID by an hypothesis
+ */
+//================================================================================
+
+void _ViscousBuilder::getIgnoreFaces(const TopoDS_Shape&             solid,
+                                     const StdMeshers_ViscousLayers* hyp,
+                                     const TopoDS_Shape&             hypShape,
+                                     set<TGeomID>&                   ignoreFaceIds)
+{
+  TopExp_Explorer exp;
+
+  vector<TGeomID> ids = hyp->GetBndShapes();
+  if ( hyp->IsToIgnoreShapes() ) // FACEs to ignore are given
+  {
+    for ( size_t ii = 0; ii < ids.size(); ++ii )
+    {
+      const TopoDS_Shape& s = getMeshDS()->IndexToShape( ids[ii] );
+      if ( !s.IsNull() && s.ShapeType() == TopAbs_FACE )
+        ignoreFaceIds.insert( ids[ii] );
+    }
+  }
+  else // FACEs with layers are given
+  {
+    exp.Init( solid, TopAbs_FACE );
+    for ( ; exp.More(); exp.Next() )
+    {
+      TGeomID faceInd = getMeshDS()->ShapeToIndex( exp.Current() );
+      if ( find( ids.begin(), ids.end(), faceInd ) == ids.end() )
+        ignoreFaceIds.insert( faceInd );
+    }
+  }
+
+  // ignore internal FACEs if inlets and outlets are specified
+  if ( hyp->IsToIgnoreShapes() )
+  {
+    TopTools_IndexedDataMapOfShapeListOfShape solidsOfFace;
+    TopExp::MapShapesAndAncestors( hypShape,
+                                   TopAbs_FACE, TopAbs_SOLID, solidsOfFace);
+
+    for ( exp.Init( solid, TopAbs_FACE ); exp.More(); exp.Next() )
+    {
+      const TopoDS_Face& face = TopoDS::Face( exp.Current() );
+      if ( SMESH_MesherHelper::NbAncestors( face, *_mesh, TopAbs_SOLID ) < 2 )
+        continue;
+
+      int nbSolids = solidsOfFace.FindFromKey( face ).Extent();
+      if ( nbSolids > 1 )
+        ignoreFaceIds.insert( getMeshDS()->ShapeToIndex( face ));
+    }
+  }
+}
+
 //================================================================================
 /*!
  * \brief Create the inner surface of the viscous layer and prepare data for infation
@@ -1940,7 +2134,6 @@ void _ViscousBuilder::limitStepSize( _SolidData& data, const double minSize )
 void _ViscousBuilder::limitStepSizeByCurvature( _SolidData& data )
 {
   const int nbTestPnt = 5; // on a FACE sub-shape
-  const double minCurvature = 0.9 / data._hyp->GetTotalThickness();
 
   BRepLProp_SLProps surfProp( 2, 1e-6 );
   SMESH_MesherHelper helper( *_mesh );
@@ -1975,6 +2168,7 @@ void _ViscousBuilder::limitStepSizeByCurvature( _SolidData& data )
       else
         continue;
       // check concavity and curvature and limit data._stepSize
+      const double minCurvature = 0.9 / data._hypOnShape[ edgesEnd ].GetTotalThickness();
       int nbLEdges = iEnd - iBeg;
       int iStep    = Max( 1, nbLEdges / nbTestPnt );
       for ( ; iBeg < iEnd; iBeg += iStep )
@@ -2069,7 +2263,16 @@ bool _ViscousBuilder::sortEdges( _SolidData&                    data,
 {
   // define allowed thickness
   computeGeomSize( data ); // compute data._geomSize
-  const double tgtThick = Min( 0.5 * data._geomSize, data._hyp->GetTotalThickness() );
+
+  data._maxThickness = 0;
+  data._minThickness = 1e100;
+  list< const StdMeshers_ViscousLayers* >::iterator hyp = data._hyps.begin();
+  for ( ; hyp != data._hyps.end(); ++hyp )
+  {
+    data._maxThickness = Max( data._maxThickness, (*hyp)->GetTotalThickness() );
+    data._minThickness = Min( data._minThickness, (*hyp)->GetTotalThickness() );
+  }
+  const double tgtThick = /*Min( 0.5 * data._geomSize, */data._maxThickness;
 
   // Find shapes needing smoothing; such a shape has _LayerEdge._normal on it's
   // boundry inclined to the shape at a sharp angle
@@ -2200,6 +2403,45 @@ bool _ViscousBuilder::sortEdges( _SolidData&                    data,
     //eVec.clear();
   }
 
+  // compute average StdMeshers_ViscousLayers parameters for each shape
+
+  data._hypOnShape.clear();
+  if ( data._hyps.size() == 1 )
+  {
+    data._hypOnShape.resize( data._endEdgeOnShape.size(), AverageHyp( data._hyps.back() ));
+  }
+  else
+  {
+    data._hypOnShape.resize( data._endEdgeOnShape.size() );
+    map< TGeomID, const StdMeshers_ViscousLayers* >::iterator f2hyp;
+    for ( size_t i = 0; i < data._endEdgeOnShape.size(); ++i )
+    {
+      int       iEnd = data._endEdgeOnShape[i];
+      _LayerEdge* LE = data._edges[ iEnd-1 ];
+      TGeomID iShape = LE->_nodes[0]->getshapeId();
+      const TopoDS_Shape& S = getMeshDS()->IndexToShape( iShape );
+      if ( S.ShapeType() == TopAbs_FACE )
+      {
+        if (( f2hyp = data._face2hyp.find( iShape )) != data._face2hyp.end() )
+        {
+          data._hypOnShape[ i ].Add( f2hyp->second );
+        }
+      }
+      else
+      {
+        PShapeIteratorPtr fIt = SMESH_MesherHelper::GetAncestors( S, *_mesh, TopAbs_FACE );
+        while ( const TopoDS_Shape* face = fIt->next() )
+        {
+          TGeomID faceID = getMeshDS()->ShapeToIndex( *face );
+          if (( f2hyp = data._face2hyp.find( faceID )) != data._face2hyp.end() )
+          {
+            data._hypOnShape[ i ].Add( f2hyp->second );
+          }
+        }
+      }
+    }
+  }
+
   return ok;
 }
 
@@ -2912,9 +3154,9 @@ bool _ViscousBuilder::inflate(_SolidData& data)
   if ( data._stepSize > 0.3 * data._geomSize )
     limitStepSize( data, 0.3 * data._geomSize );
 
-  const double tgtThick = data._hyp->GetTotalThickness();
+  const double tgtThick = data._maxThickness;
-  if ( data._stepSize > tgtThick )
+  if ( data._stepSize > data._minThickness )
-    limitStepSize( data, tgtThick );
+    limitStepSize( data, data._minThickness );
 
   if ( data._stepSize < 1. )
     data._epsilon = data._stepSize * 1e-7;
@@ -2923,21 +3165,26 @@ bool _ViscousBuilder::inflate(_SolidData& data)
 
   double avgThick = 0, curThick = 0, distToIntersection = Precision::Infinite();
   int nbSteps = 0, nbRepeats = 0;
-  while ( 1.01 * avgThick < tgtThick )
+  int iBeg, iEnd, iS;
+  while ( avgThick < 0.99 )
   {
     // new target length
     curThick += data._stepSize;
     if ( curThick > tgtThick )
     {
-      curThick = tgtThick + ( tgtThick-avgThick ) * nbRepeats;
+      curThick = tgtThick + tgtThick*( 1.-avgThick ) * nbRepeats;
       nbRepeats++;
     }
 
     // Elongate _LayerEdge's
     dumpFunction(SMESH_Comment("inflate")<<data._index<<"_step"<<nbSteps); // debug
-    for ( size_t i = 0; i < data._edges.size(); ++i )
+    for ( iBeg = 0, iS = 0; iS < data._endEdgeOnShape.size(); ++iS )
     {
-      data._edges[i]->SetNewLength( curThick, helper );
+      const double shapeCurThick = Min( curThick, data._hypOnShape[ iS ].GetTotalThickness() );
+      for ( iEnd = data._endEdgeOnShape[ iS ]; iBeg < iEnd; ++iBeg )
+      {
+        data._edges[iBeg]->SetNewLength( shapeCurThick, helper );
+      }
     }
     dumpFunctionEnd();
 
@@ -2962,16 +3209,22 @@ bool _ViscousBuilder::inflate(_SolidData& data)
 
     // Evaluate achieved thickness
     avgThick = 0;
-    for ( size_t i = 0; i < data._edges.size(); ++i )
+    for ( iBeg = 0, iS = 0; iS < data._endEdgeOnShape.size(); ++iS )
-      avgThick += data._edges[i]->_len;
+    {
+      const double shapeTgtThick = data._hypOnShape[ iS ].GetTotalThickness();
+      for ( iEnd = data._endEdgeOnShape[ iS ]; iBeg < iEnd; ++iBeg )
+      {
+        avgThick += Min( 1., data._edges[iBeg]->_len / shapeTgtThick );
+      }
+    }
     avgThick /= data._edges.size();
-    debugMsg( "-- Thickness " << avgThick << " reached" );
+    debugMsg( "-- Thickness " << avgThick*100 << "% reached" );
 
-    if ( distToIntersection < avgThick*1.5 )
+    if ( distToIntersection < tgtThick*avgThick*1.5 )
     {
       debugMsg( "-- Stop inflation since "
                 << " distToIntersection( "<<distToIntersection<<" ) < avgThick( "
-                << avgThick << " ) * 1.5" );
+                << tgtThick*avgThick << " ) * 1.5" );
       break;
     }
     // new step size
@@ -2980,12 +3233,12 @@ bool _ViscousBuilder::inflate(_SolidData& data)
       data._stepSize = data._stepSizeCoeff *
         SMESH_TNodeXYZ(data._stepSizeNodes[0]).Distance(data._stepSizeNodes[1]);
 
-  } // while ( 1.01 * avgThick < tgtThick )
+  } // while ( avgThick < 0.99 )
 
   if (nbSteps == 0 )
     return error("failed at the very first inflation step", data._index);
 
-  if ( 1.01 * avgThick < tgtThick )
+  if ( avgThick < 0.99 )
     if ( SMESH_subMesh* sm = _mesh->GetSubMeshContaining( data._index ))
     {
       SMESH_ComputeErrorPtr& smError = sm->GetComputeError();
@@ -2994,14 +3247,13 @@ bool _ViscousBuilder::inflate(_SolidData& data)
           ( new SMESH_ComputeError (COMPERR_WARNING,
                                     SMESH_Comment("Thickness ") << tgtThick <<
                                     " of viscous layers not reached,"
-                                    " average reached thickness is " << avgThick ));
+                                    " average reached thickness is " << avgThick*100 << "%."));
     }
 
 
   // Restore position of src nodes moved by infaltion on _noShrinkShapes
   dumpFunction(SMESH_Comment("restoNoShrink_So")<<data._index); // debug
-  int iBeg, iEnd = 0;
+  for ( iEnd = iS = 0; iS < data._endEdgeOnShape.size(); ++iS )
-  for ( int iS = 0; iS < data._endEdgeOnShape.size(); ++iS )
   {
     iBeg = iEnd;
     iEnd = data._endEdgeOnShape[ iS ];
@@ -3041,6 +3293,16 @@ bool _ViscousBuilder::smoothAndCheck(_SolidData& data,
     iBeg = iEnd;
     iEnd = data._endEdgeOnShape[ iS ];
 
+    // bool toSmooth = false;
+    // for ( int i = iBeg; i < iEnd; ++i )
+    //   toSmooth = data._edges[ iBeg ]->NbSteps() >= nbSteps+1;
+    // if ( !toSmooth )
+    // {
+    //   if ( iS+1 == data._nbShapesToSmooth )
+    //     data._nbShapesToSmooth--;
+    //   continue; // target length reached some steps before
+    // }
+
     if ( !data._edges[ iBeg ]->_sWOL.IsNull() &&
          data._edges[ iBeg ]->_sWOL.ShapeType() == TopAbs_FACE )
     {
@@ -3089,10 +3351,10 @@ bool _ViscousBuilder::smoothAndCheck(_SolidData& data,
         badNb = 0;
         moved = false;
         if ( step % 2 )
-          for ( int i = iBeg; i < iEnd; ++i )
+          for ( int i = iBeg; i < iEnd; ++i ) // iterate forward
             moved |= data._edges[i]->Smooth(badNb);
         else
-          for ( int i = iEnd-1; i >= iBeg; --i )
+          for ( int i = iEnd-1; i >= iBeg; --i ) // iterate backward
             moved |= data._edges[i]->Smooth(badNb);
         improved = ( badNb < oldBadNb );
 
@@ -3330,14 +3592,14 @@ void _SolidData::SortOnEdge( const TopoDS_Edge&  E,
 //================================================================================
 
 bool _SolidData::GetShapeEdges(const TGeomID shapeID,
-                               size_t &      edgesEnd,
+                               size_t &      iEdgesEnd,
                                int*          iBeg,
                                int*          iEnd ) const
 {
   int beg = 0, end = 0;
-  for ( edgesEnd = 0; edgesEnd < _endEdgeOnShape.size(); ++edgesEnd )
+  for ( iEdgesEnd = 0; iEdgesEnd < _endEdgeOnShape.size(); ++iEdgesEnd )
   {
-    end = _endEdgeOnShape[ edgesEnd ];
+    end = _endEdgeOnShape[ iEdgesEnd ];
     TGeomID sID = _edges[ beg ]->_nodes[0]->getshapeId();
     if ( sID == shapeID )
     {
@@ -4699,7 +4961,7 @@ void _LayerEdge::SetNewLength( double len, SMESH_MesherHelper& helper )
 {
   if ( _len - len > -1e-6 )
   {
-    _pos.push_back( _pos.back() );
+    //_pos.push_back( _pos.back() );
     return;
   }
 
@@ -4809,6 +5071,8 @@ bool _ViscousBuilder::refine(_SolidData& data)
 
   // Create intermediate nodes on each _LayerEdge
 
+  int iS = 0, iEnd = data._endEdgeOnShape[ iS ];
+
   for ( size_t i = 0; i < data._edges.size(); ++i )
   {
     _LayerEdge& edge = *data._edges[i];
@@ -4816,6 +5080,11 @@ bool _ViscousBuilder::refine(_SolidData& data)
     if ( edge._nodes.size() < 2 )
       continue; // on _noShrinkShapes
 
+    // get parameters of layers for the edge
+    if ( i == iEnd )
+      iEnd = data._endEdgeOnShape[ ++iS ];
+    const AverageHyp& hyp = data._hypOnShape[ iS ];
+
     // get accumulated length of segments
     vector< double > segLen( edge._pos.size() );
     segLen[0] = 0.0;
@@ -4826,7 +5095,7 @@ bool _ViscousBuilder::refine(_SolidData& data)
     const SMDS_MeshNode* tgtNode = edge._nodes.back();
     if ( edge._nodes.size() == 2 )
     {
-      edge._nodes.resize( data._hyp->GetNumberLayers() + 1, 0 );
+      edge._nodes.resize( hyp.GetNumberLayers() + 1, 0 );
       edge._nodes[1] = 0;
       edge._nodes.back() = tgtNode;
     }
@@ -4875,8 +5144,8 @@ bool _ViscousBuilder::refine(_SolidData& data)
     // calculate height of the first layer
     double h0;
     const double T = segLen.back(); //data._hyp.GetTotalThickness();
-    const double f = data._hyp->GetStretchFactor();
+    const double f = hyp.GetStretchFactor();
-    const int    N = data._hyp->GetNumberLayers();
+    const int    N = hyp.GetNumberLayers();
     const double fPowN = pow( f, N );
     if ( fPowN - 1 <= numeric_limits<double>::min() )
       h0 = T / N;
@@ -4995,8 +5264,10 @@ bool _ViscousBuilder::refine(_SolidData& data)
   TopExp_Explorer exp( data._solid, TopAbs_FACE );
   for ( ; exp.More(); exp.Next() )
   {
-    if ( data._ignoreFaceIds.count( getMeshDS()->ShapeToIndex( exp.Current() )))
+    const TGeomID faceID = getMeshDS()->ShapeToIndex( exp.Current() );
+    if ( data._ignoreFaceIds.count( faceID ))
       continue;
+    const bool isReversedFace = data._reversedFaceIds.count( faceID );
     SMESHDS_SubMesh*    fSubM = getMeshDS()->MeshElements( exp.Current() );
     SMDS_ElemIteratorPtr  fIt = fSubM->GetElements();
     while ( fIt->more() )
@@ -5011,14 +5282,15 @@ bool _ViscousBuilder::refine(_SolidData& data)
       for ( int iN = 0; iN < nbNodes; ++iN )
       {
         const SMDS_MeshNode* n = nIt->next();
-        nnVec[ iN ] = & data._n2eMap[ n ]->_nodes;
+        const int i = isReversedFace ? nbNodes-1-iN : iN;
-        if ( nnVec[ iN ]->size() < 2 )
+        nnVec[ i ] = & data._n2eMap[ n ]->_nodes;
+        if ( nnVec[ i ]->size() < 2 )
           degenEdgeInd.insert( iN );
         else
-          nbZ = nnVec[ iN ]->size();
+          nbZ = nnVec[ i ]->size();
 
         if ( helper.HasDegeneratedEdges() )
-          nnSet.insert( nnVec[ iN ]);
+          nnSet.insert( nnVec[ i ]);
       }
       if ( nbZ == 0 )
         continue;

src/StdMeshers/StdMeshers_ViscousLayers.hxx

@@ -28,6 +28,7 @@
 
 #include "SMESH_Hypothesis.hxx"
 #include "SMESH_ProxyMesh.hxx"
+#include "SMESH_ComputeError.hxx"
 
 #include <vector>
 
@@ -39,7 +40,7 @@ class STDMESHERS_EXPORT StdMeshers_ViscousLayers : public SMESH_Hypothesis
 public:
   StdMeshers_ViscousLayers(int hypId, int studyId, SMESH_Gen* gen);
 
-  // Set boundary shapes, faces in 3D, edges in 2D, either to exclude from
+  // Set boundary shapes (faces in 3D, edges in 2D) either to exclude from
   // treatment or to make the Viscous Layers on
   void SetBndShapes(const std::vector<int>& shapeIds, bool toIgnore);
   std::vector<int> GetBndShapes() const { return _shapeIds; }
@@ -63,6 +64,15 @@ public:
                                const TopoDS_Shape& theShape,
                                const bool          toMakeN2NMap=false) const;
 
+  // Checks compatibility of assigned StdMeshers_ViscousLayers hypotheses 
+  static SMESH_ComputeErrorPtr
+    CheckHypothesis(SMESH_Mesh&                          aMesh,
+                    const TopoDS_Shape&                  aShape,
+                    SMESH_Hypothesis::Hypothesis_Status& aStatus);
+
+  // Checks if viscous layers should be constructed on a shape
+  bool IsShapeWithLayers(int shapeIndex) const;
+
   virtual std::ostream & SaveTo(std::ostream & save);
   virtual std::istream & LoadFrom(std::istream & load);
 

src/StdMeshers/StdMeshers_ViscousLayers2D.cxx

@@ -256,6 +256,7 @@ namespace VISCOUS_2D
     _PolyLine*           _rightLine;
     int                  _firstPntInd; // index in vector<UVPtStruct> of _wire
     int                  _lastPntInd;
+    int                  _index;       // index in _ViscousBuilder2D::_polyLineVec
 
     vector< _LayerEdge > _lEdges;      /* _lEdges[0] is usually is not treated
                                           as it is equal to the last one of the _leftLine */
@@ -325,6 +326,7 @@ namespace VISCOUS_2D
   //--------------------------------------------------------------------------------
 
   typedef map< const SMDS_MeshNode*, _LayerEdge*, TIDCompare > TNode2Edge;
+  typedef StdMeshers_ViscousLayers2D                           THypVL;
   
   //--------------------------------------------------------------------------------
   /*!
@@ -335,14 +337,17 @@ namespace VISCOUS_2D
   public:
     _ViscousBuilder2D(SMESH_Mesh&                       theMesh,
                       const TopoDS_Face&                theFace,
-                      const StdMeshers_ViscousLayers2D* theHyp);
+                      vector< const THypVL* > &         theHyp,
+                      vector< TopoDS_Shape > &          theHypShapes);
     SMESH_ComputeErrorPtr GetError() const { return _error; }
     // does it's job
-    SMESH_ProxyMesh::Ptr  Compute(const TopoDS_Shape& theShapeHypAssignedTo);
+    SMESH_ProxyMesh::Ptr  Compute();
 
   private:
 
-    bool findEdgesWithLayers(const TopoDS_Shape& theShapeHypAssignedTo);
+    friend class ::StdMeshers_ViscousLayers2D;
+
+    bool findEdgesWithLayers();
     bool makePolyLines();
     bool inflate();
     bool fixCollisions();
@@ -362,9 +367,13 @@ namespace VISCOUS_2D
                            GeomAPI_ProjectPointOnSurf* faceProj);
     void adjustCommonEdge( _PolyLine& LL, _PolyLine& LR );
     void calcLayersHeight(const double    totalThick,
-                          vector<double>& heights);
+                          vector<double>& heights,
+                          const THypVL*   hyp);
     bool removeMeshFaces(const TopoDS_Shape& face);
 
+    const THypVL*     getLineHypothesis(int iPL);
+    double            getLineThickness (int iPL);
+
     bool              error( const string& text );
     SMESHDS_Mesh*     getMeshDS() { return _mesh->GetMeshDS(); }
     _ProxyMeshOfFace* getProxyMesh();
@@ -377,7 +386,8 @@ namespace VISCOUS_2D
     // input data
     SMESH_Mesh*                 _mesh;
     TopoDS_Face                 _face;
-    const StdMeshers_ViscousLayers2D* _hyp;
+    vector< const THypVL* >     _hyps;
+    vector< TopoDS_Shape >      _hypShapes;
 
     // result data
     SMESH_ProxyMesh::Ptr        _proxyMesh;
@@ -388,11 +398,12 @@ namespace VISCOUS_2D
     SMESH_MesherHelper          _helper;
     TSideVector                 _faceSideVec; // wires (StdMeshers_FaceSide) of _face
     vector<_PolyLine>           _polyLineVec; // fronts to advance
+    vector< const THypVL* >     _hypOfEdge; // a hyp per an EDGE of _faceSideVec
     bool                        _is2DIsotropic; // is same U and V resoulution of _face
     vector<TopoDS_Face>         _clearedFaces; // FACEs whose mesh was removed by shrink()
 
-    double                      _fPowN; // to compute thickness of layers
+    //double                      _fPowN; // to compute thickness of layers
-    double                      _thickness; // required or possible layers thickness
+    double                      _maxThickness; // max possible layers thickness
 
     // sub-shapes of _face 
     set<TGeomID>                _ignoreShapeIds; // ids of EDGEs w/o layers
@@ -409,15 +420,32 @@ namespace VISCOUS_2D
   /*!
    * \brief Returns StdMeshers_ViscousLayers2D for the FACE
    */
-  const StdMeshers_ViscousLayers2D* findHyp(SMESH_Mesh&        theMesh,
+  bool findHyps(SMESH_Mesh&                                   theMesh,
                 const TopoDS_Face&                            theFace,
-                                            TopoDS_Shape*      assignedTo=0)
+                vector< const StdMeshers_ViscousLayers2D* > & theHyps,
+                vector< TopoDS_Shape > &                      theAssignedTo)
   {
+    theHyps.clear();
+    theAssignedTo.clear();
     SMESH_HypoFilter hypFilter
       ( SMESH_HypoFilter::HasName( StdMeshers_ViscousLayers2D::GetHypType() ));
-    const SMESH_Hypothesis * hyp =
+    list< const SMESHDS_Hypothesis * > hypList;
-      theMesh.GetHypothesis( theFace, hypFilter, /*ancestors=*/true, assignedTo );
+    list< TopoDS_Shape >               hypShapes;
-    return dynamic_cast< const StdMeshers_ViscousLayers2D* > ( hyp );
+    int nbHyps = theMesh.GetHypotheses
+      ( theFace, hypFilter, hypList, /*ancestors=*/true, &hypShapes );
+    if ( nbHyps )
+    {
+      theHyps.reserve( nbHyps );
+      theAssignedTo.reserve( nbHyps );
+      list< const SMESHDS_Hypothesis * >::iterator hyp = hypList.begin();
+      list< TopoDS_Shape >::iterator               shape = hypShapes.begin();
+      for ( ; hyp != hypList.end(); ++hyp, ++shape )
+      {
+        theHyps.push_back( static_cast< const StdMeshers_ViscousLayers2D* > ( *hyp ));
+        theAssignedTo.push_back( *shape );
+      }
+    }
+    return nbHyps;
   }
 
   //================================================================================
@@ -436,7 +464,7 @@ namespace VISCOUS_2D
                         const SMESHDS_Mesh*               theMesh,
                         set< int > &                      theEdgeIds)
   {
-    int nbToEdgesIgnore = 0;
+    int nbEdgesToIgnore = 0;
     vector<TGeomID> ids = theHyp->GetBndShapes();
     if ( theHyp->IsToIgnoreShapes() ) // EDGEs to ignore are given
     {
@@ -448,20 +476,20 @@ namespace VISCOUS_2D
              SMESH_MesherHelper::IsSubShape( E, theFace ))
         {
           theEdgeIds.insert( ids[i] );
-          ++nbToEdgesIgnore;
+          ++nbEdgesToIgnore;
         }
       }
     }
     else // EDGEs to make the Viscous Layers on are given
     {
       TopExp_Explorer E( theFace, TopAbs_EDGE );
-      for ( ; E.More(); E.Next(), ++nbToEdgesIgnore )
+      for ( ; E.More(); E.Next(), ++nbEdgesToIgnore )
         theEdgeIds.insert( theMesh->ShapeToIndex( E.Current() ));
 
       for ( size_t i = 0; i < ids.size(); ++i )
-        nbToEdgesIgnore -= theEdgeIds.erase( ids[i] );
+        nbEdgesToIgnore -= theEdgeIds.erase( ids[i] );
     }
-    return nbToEdgesIgnore;
+    return nbEdgesToIgnore;
   }
 
 } // namespace VISCOUS_2D
@@ -489,12 +517,12 @@ StdMeshers_ViscousLayers2D::Compute(SMESH_Mesh&        theMesh,
 {
   SMESH_ProxyMesh::Ptr pm;
 
-  TopoDS_Shape hypAssignedTo;
+  vector< const StdMeshers_ViscousLayers2D* > hyps;
-  const StdMeshers_ViscousLayers2D* vlHyp = VISCOUS_2D::findHyp( theMesh, theFace, &hypAssignedTo );
+  vector< TopoDS_Shape >                      hypShapes;
-  if ( vlHyp )
+  if ( VISCOUS_2D::findHyps( theMesh, theFace, hyps, hypShapes ))
   {
-    VISCOUS_2D::_ViscousBuilder2D builder( theMesh, theFace, vlHyp );
+    VISCOUS_2D::_ViscousBuilder2D builder( theMesh, theFace, hyps, hypShapes );
-    pm = builder.Compute( hypAssignedTo );
+    pm = builder.Compute();
     SMESH_ComputeErrorPtr error = builder.GetError();
     if ( error && !error->IsOK() )
       theMesh.GetSubMesh( theFace )->GetComputeError() = error;
@@ -510,6 +538,38 @@ StdMeshers_ViscousLayers2D::Compute(SMESH_Mesh&        theMesh,
   return pm;
 }
 // --------------------------------------------------------------------------------
+SMESH_ComputeErrorPtr
+StdMeshers_ViscousLayers2D::CheckHypothesis(SMESH_Mesh&                          theMesh,
+                                            const TopoDS_Shape&                  theShape,
+                                            SMESH_Hypothesis::Hypothesis_Status& theStatus)
+{
+  SMESH_ComputeErrorPtr error = SMESH_ComputeError::New(COMPERR_OK);
+  theStatus = SMESH_Hypothesis::HYP_OK;
+
+  TopExp_Explorer exp( theShape, TopAbs_FACE );
+  for ( ; exp.More() && theStatus == SMESH_Hypothesis::HYP_OK; exp.Next() )
+  {
+    const TopoDS_Face& face = TopoDS::Face( exp.Current() );
+    vector< const StdMeshers_ViscousLayers2D* > hyps;
+    vector< TopoDS_Shape >                      hypShapes;
+    if ( VISCOUS_2D::findHyps( theMesh, face, hyps, hypShapes ))
+    {
+      VISCOUS_2D::_ViscousBuilder2D builder( theMesh, face, hyps, hypShapes );
+      builder._faceSideVec =
+        StdMeshers_FaceSide::GetFaceWires( face, theMesh, true, error,
+                                           SMESH_ProxyMesh::Ptr(),
+                                           /*theCheckVertexNodes=*/false);
+      if ( error->IsOK() && !builder.findEdgesWithLayers())
+      {
+        error = builder.GetError();
+        if ( error && !error->IsOK() )
+          theStatus = SMESH_Hypothesis::HYP_INCOMPAT_HYPS;
+      }
+    }
+  }
+  return error;
+}
+// --------------------------------------------------------------------------------
 void StdMeshers_ViscousLayers2D::RestoreListeners() const
 {
   StudyContextStruct* sc = _gen->GetStudyContext( _studyId );
@@ -549,17 +609,20 @@ using namespace VISCOUS_2D;
 
 _ViscousBuilder2D::_ViscousBuilder2D(SMESH_Mesh&               theMesh,
                                      const TopoDS_Face&        theFace,
-                                     const StdMeshers_ViscousLayers2D* theHyp):
+                                     vector< const THypVL* > & theHyps,
-  _mesh( &theMesh ), _face( theFace ), _hyp( theHyp ), _helper( theMesh )
+                                     vector< TopoDS_Shape > &  theAssignedTo):
+  _mesh( &theMesh ), _face( theFace ), _helper( theMesh )
 {
+  _hyps.swap( theHyps );
+  _hypShapes.swap( theAssignedTo );
+
   _helper.SetSubShape( _face );
   _helper.SetElementsOnShape( true );
 
   _face.Orientation( TopAbs_FORWARD ); // 2D logic works only in this case
   _surface = BRep_Tool::Surface( _face );
 
-  if ( _hyp )
+  _error = SMESH_ComputeError::New(COMPERR_OK);
-    _fPowN = pow( _hyp->GetStretchFactor(), _hyp->GetNumberLayers() );
 
   _nbLE = 0;
 }
@@ -593,14 +656,14 @@ bool _ViscousBuilder2D::error(const string& text )
  */
 //================================================================================
 
-SMESH_ProxyMesh::Ptr _ViscousBuilder2D::Compute(const TopoDS_Shape& theShapeHypAssignedTo)
+SMESH_ProxyMesh::Ptr _ViscousBuilder2D::Compute()
 {
-  _error       = SMESH_ComputeError::New(COMPERR_OK);
   _faceSideVec = StdMeshers_FaceSide::GetFaceWires( _face, *_mesh, true, _error);
+
   if ( !_error->IsOK() )
     return _proxyMesh;
 
-  if ( !findEdgesWithLayers(theShapeHypAssignedTo) ) // analysis of a shape
+  if ( !findEdgesWithLayers() ) // analysis of a shape
     return _proxyMesh;
 
   if ( ! makePolyLines() ) // creation of fronts
@@ -629,21 +692,79 @@ SMESH_ProxyMesh::Ptr _ViscousBuilder2D::Compute(const TopoDS_Shape& theShapeHypA
  */
 //================================================================================
 
-bool _ViscousBuilder2D::findEdgesWithLayers(const TopoDS_Shape& theShapeHypAssignedTo)
+bool _ViscousBuilder2D::findEdgesWithLayers()
 {
-  // collect all EDGEs to ignore defined by hyp
+  // collect all EDGEs to ignore defined by _hyps
-  int nbMyEdgesIgnored = getEdgesToIgnore( _hyp, _face, getMeshDS(), _ignoreShapeIds );
+  typedef std::pair< set<TGeomID>, const THypVL* > TEdgesOfHyp;
+  vector< TEdgesOfHyp > ignoreEdgesOfHyp( _hyps.size() );
+  for ( size_t i = 0; i < _hyps.size(); ++i )
+  {
+    ignoreEdgesOfHyp[i].second = _hyps[i];
+    getEdgesToIgnore( _hyps[i], _face, getMeshDS(), ignoreEdgesOfHyp[i].first );
+  }
 
   // get all shared EDGEs
   TopTools_MapOfShape sharedEdges;
+  TopTools_IndexedMapOfShape hypFaces; // faces with VL hyps
+  for ( size_t i = 0; i < _hypShapes.size(); ++i )
+    TopExp::MapShapes( _hypShapes[i], TopAbs_FACE, hypFaces );
   TopTools_IndexedDataMapOfShapeListOfShape facesOfEdgeMap;
-  TopExp::MapShapesAndAncestors( theShapeHypAssignedTo,
+  for ( int iF = 1; iF <= hypFaces.Extent(); ++iF )
-                                 TopAbs_EDGE, TopAbs_FACE, facesOfEdgeMap);
+    TopExp::MapShapesAndAncestors( hypFaces(iF), TopAbs_EDGE, TopAbs_FACE, facesOfEdgeMap);
   for ( int iE = 1; iE <= facesOfEdgeMap.Extent(); ++iE )
     if ( facesOfEdgeMap( iE ).Extent() > 1 )
       sharedEdges.Add( facesOfEdgeMap.FindKey( iE ));
 
-  // check all EDGEs of the _face
+  // fill _hypOfEdge
+  if ( _hyps.size() > 1 )
+  {
+    // check if two hypotheses define different parameters for the same EDGE
+    for ( size_t iWire = 0; iWire < _faceSideVec.size(); ++iWire )
+    {
+      StdMeshers_FaceSidePtr wire = _faceSideVec[ iWire ];
+      for ( int iE = 0; iE < wire->NbEdges(); ++iE )
+      {
+        const THypVL* hyp = 0;
+        const TGeomID edgeID = wire->EdgeID( iE );
+        if ( !sharedEdges.Contains( wire->Edge( iE )))
+        {
+          for ( size_t i = 0; i < ignoreEdgesOfHyp.size(); ++i )
+            if ( ! ignoreEdgesOfHyp[i].first.count( edgeID ))
+            {
+              if ( hyp )
+                return error(SMESH_Comment("Several hypotheses define "
+                                           "Viscous Layers on the edge #") << edgeID );
+              hyp = ignoreEdgesOfHyp[i].second;
+            }
+        }
+        _hypOfEdge.push_back( hyp );
+        if ( !hyp )
+          _ignoreShapeIds.insert( edgeID );
+      }
+      // check if two hypotheses define different number of viscous layers for
+      // adjacent EDGEs
+      const THypVL *hyp, *prevHyp = _hypOfEdge.back();
+      size_t iH = _hypOfEdge.size() - wire->NbEdges();
+      for ( ; iH < _hypOfEdge.size(); ++iH )
+      {
+        hyp = _hypOfEdge[ iH ];
+        if ( hyp && prevHyp &&
+             hyp->GetNumberLayers() != prevHyp->GetNumberLayers() )
+        {
+          return error("Two hypotheses define different number of "
+                       "viscous layers on adjacent edges");
+        }
+        prevHyp = hyp;
+      }
+    }
+  }
+  else if ( _hyps.size() == 1 )
+  {
+    _ignoreShapeIds.swap( ignoreEdgesOfHyp[0].first );
+  }
+
+  // check all EDGEs of the _face to fill _ignoreShapeIds and _noShrinkVert
+
   int totalNbEdges = 0;
   for ( size_t iWire = 0; iWire < _faceSideVec.size(); ++iWire )
   {
@@ -674,9 +795,9 @@ bool _ViscousBuilder2D::findEdgesWithLayers(const TopoDS_Shape& theShapeHypAssig
           for ( ; hyp != allHyps.end() && !viscHyp; ++hyp )
             viscHyp = dynamic_cast<const StdMeshers_ViscousLayers2D*>( *hyp );
 
-          set<TGeomID> neighbourIgnoreEdges;
+          // set<TGeomID> neighbourIgnoreEdges;
-          if (viscHyp)
+          // if (viscHyp)
-            getEdgesToIgnore( viscHyp, neighbourFace, getMeshDS(), neighbourIgnoreEdges );
+          //   getEdgesToIgnore( viscHyp, neighbourFace, getMeshDS(), neighbourIgnoreEdges );
 
           for ( int iV = 0; iV < 2; ++iV )
           {
@@ -688,9 +809,18 @@ bool _ViscousBuilder2D::findEdgesWithLayers(const TopoDS_Shape& theShapeHypAssig
               PShapeIteratorPtr edgeIt = _helper.GetAncestors( vertex, *_mesh, TopAbs_EDGE );
               while ( const TopoDS_Shape* edge = edgeIt->next() )
                 if ( !edge->IsSame( wire->Edge( iE )) &&
-                     _helper.IsSubShape( *edge, neighbourFace ) &&
+                     _helper.IsSubShape( *edge, neighbourFace ))
-                     ( neighbourIgnoreEdges.count( getMeshDS()->ShapeToIndex( *edge )) ||
+                {
-                       sharedEdges.Contains( *edge )))
+                  const TGeomID neighbourID = getMeshDS()->ShapeToIndex( *edge );
+                  bool hasVL = !sharedEdges.Contains( *edge );
+                  if ( hasVL )
+                  {
+                    hasVL = false;
+                    for ( hyp = allHyps.begin(); hyp != allHyps.end() && !hasVL; ++hyp )
+                      if ( viscHyp = dynamic_cast<const THypVL*>( *hyp ))
+                        hasVL = viscHyp->IsShapeWithLayers( neighbourID );
+                  }
+                  if ( !hasVL )
                   {
                     _noShrinkVert.insert( getMeshDS()->ShapeToIndex( vertex ));
                     break;
@@ -701,19 +831,22 @@ bool _ViscousBuilder2D::findEdgesWithLayers(const TopoDS_Shape& theShapeHypAssig
         }
       }
     }
+  }
+
+  int nbMyEdgesIgnored = _ignoreShapeIds.size();
 
   // add VERTEXes w/o layers to _ignoreShapeIds (this is used by toShrinkForAdjacent())
-  for ( size_t iWire = 0; iWire < _faceSideVec.size(); ++iWire )
+  // for ( size_t iWire = 0; iWire < _faceSideVec.size(); ++iWire )
-  {
+  // {
-    StdMeshers_FaceSidePtr wire = _faceSideVec[ iWire ];
+  //   StdMeshers_FaceSidePtr wire = _faceSideVec[ iWire ];
-    for ( int iE = 0; iE < wire->NbEdges(); ++iE )
+  //   for ( int iE = 0; iE < wire->NbEdges(); ++iE )
-    {
+  //   {
-      TGeomID edge1 = wire->EdgeID( iE );
+  //     TGeomID edge1 = wire->EdgeID( iE );
-      TGeomID edge2 = wire->EdgeID( iE+1 );
+  //     TGeomID edge2 = wire->EdgeID( iE+1 );
-      if ( _ignoreShapeIds.count( edge1 ) && _ignoreShapeIds.count( edge2 ))
+  //     if ( _ignoreShapeIds.count( edge1 ) && _ignoreShapeIds.count( edge2 ))
-        _ignoreShapeIds.insert( getMeshDS()->ShapeToIndex( wire->LastVertex( iE )));
+  //       _ignoreShapeIds.insert( getMeshDS()->ShapeToIndex( wire->LastVertex( iE )));
-    }
+  //   }
-  }
+  // }
 
   return ( nbMyEdgesIgnored < totalNbEdges );
 }
@@ -772,6 +905,7 @@ bool _ViscousBuilder2D::makePolyLines()
     for ( int iE = 0; iE < wire->NbEdges(); ++iE )
     {
       _PolyLine& L  = _polyLineVec[ iPoLine++ ];
+      L._index      = iPoLine-1;
       L._wire       = wire.get();
       L._edgeInd    = iE;
       L._advancable = !_ignoreShapeIds.count( wire->EdgeID( iE ));
@@ -846,13 +980,16 @@ bool _ViscousBuilder2D::makePolyLines()
   // Evaluate max possible _thickness if required layers thickness seems too high
   // ----------------------------------------------------------------------------
 
-  _thickness = _hyp->GetTotalThickness();
+  _maxThickness = _hyps[0]->GetTotalThickness();
+  for ( size_t iH = 1; iH < _hyps.size(); ++iH )
+    _maxThickness = Max( _maxThickness, _hyps[iH]->GetTotalThickness() );
+
   _SegmentTree::box_type faceBndBox2D;
   for ( iPoLine = 0; iPoLine < _polyLineVec.size(); ++iPoLine )
     faceBndBox2D.Add( *_polyLineVec[ iPoLine]._segTree->getBox() );
-  double boxTol = 1e-3 * sqrt( faceBndBox2D.SquareExtent() );
+  const double boxTol = 1e-3 * sqrt( faceBndBox2D.SquareExtent() );
-  //
+
-  if ( _thickness * maxLen2dTo3dRatio > sqrt( faceBndBox2D.SquareExtent() ) / 10 )
+  if ( _maxThickness * maxLen2dTo3dRatio > sqrt( faceBndBox2D.SquareExtent() ) / 10 )
   {
     vector< const _Segment* > foundSegs;
     double maxPossibleThick = 0;
@@ -885,7 +1022,7 @@ bool _ViscousBuilder2D::makePolyLines()
       }
     }
     if ( maxPossibleThick > 0. )
-      _thickness = Min( _hyp->GetTotalThickness(), maxPossibleThick );
+      _maxThickness = Min( _maxThickness, maxPossibleThick );
   }
 
   // Adjust _LayerEdge's at _PolyLine's extremities
@@ -930,13 +1067,14 @@ bool _ViscousBuilder2D::makePolyLines()
   for ( iPoLine = 0; iPoLine < _polyLineVec.size(); ++iPoLine )
   {
     lineBoxes[ iPoLine ] = *_polyLineVec[ iPoLine ]._segTree->getBox();
-    lineBoxes[ iPoLine ].Enlarge( maxLen2dTo3dRatio * _thickness * 
+    lineBoxes[ iPoLine ].Enlarge( maxLen2dTo3dRatio * getLineThickness( iPoLine ) * 
                                   ( _polyLineVec[ iPoLine ]._advancable ? 2. : 1.2 ));
   }
   // _reachableLines
   for ( iPoLine = 0; iPoLine < _polyLineVec.size(); ++iPoLine )
   {
     _PolyLine& L1 = _polyLineVec[ iPoLine ];
+    const double thick1 = getLineThickness( iPoLine );
     for ( size_t iL2 = 0; iL2 < _polyLineVec.size(); ++iL2 )
     {
       _PolyLine& L2 = _polyLineVec[ iL2 ];
@@ -950,7 +1088,7 @@ bool _ViscousBuilder2D::makePolyLines()
       {
         _LayerEdge& LE = L1._lEdges[iLE];
         if ( !lineBoxes[ iL2 ].IsOut ( LE._uvOut,
-                                       LE._uvOut + LE._normal2D *_thickness * LE._len2dTo3dRatio ))
+                                       LE._uvOut + LE._normal2D * thick1 * LE._len2dTo3dRatio ))
         {
           L1._reachableLines.push_back( & L2 );
           break;
@@ -1024,7 +1162,7 @@ void _ViscousBuilder2D::adjustCommonEdge( _PolyLine& LL, _PolyLine& LR )
       // during inflate().
       //
       // find max length of the VERTEX-based _LayerEdge whose direction is normAvg
-      double maxLen2D       = _thickness * EL._len2dTo3dRatio;
+      double       maxLen2D  = _maxThickness * EL._len2dTo3dRatio;
       const gp_XY& pCommOut  = ER._uvOut;
       gp_XY        pCommIn   = pCommOut + normAvg * maxLen2D;
       _Segment segCommon( pCommOut, pCommIn );
@@ -1067,7 +1205,7 @@ void _ViscousBuilder2D::adjustCommonEdge( _PolyLine& LL, _PolyLine& LR )
         _SegmentIntersection lastIntersection;
         for ( ; iLE < L._lEdges.size(); ++iLE, eIt += dIt )
         {
-          gp_XY uvIn = eIt->_uvOut + eIt->_normal2D * _thickness * eIt->_len2dTo3dRatio;
+          gp_XY uvIn = eIt->_uvOut + eIt->_normal2D * _maxThickness * eIt->_len2dTo3dRatio;
           _Segment segOfEdge( eIt->_uvOut, uvIn );
           if ( !intersection.Compute( segCommon, segOfEdge ))
             break;
@@ -1148,7 +1286,7 @@ void _ViscousBuilder2D::setLayerEdgeData( _LayerEdge&                 lEdge,
     gp_Vec faceNorm = du ^ dv;
     gp_Vec normal   = faceNorm ^ tangent;
     normal.Normalize();
-    p = pOut.XYZ() + normal.XYZ() * /*1e-2 * */_hyp->GetTotalThickness() / _hyp->GetNumberLayers();
+    p = pOut.XYZ() + normal.XYZ() * /*1e-2 * */_hyps[0]->GetTotalThickness() / _hyps[0]->GetNumberLayers();
     faceProj->Perform( p );
     if ( !faceProj->IsDone() || faceProj->NbPoints() < 1 )
       return setLayerEdgeData( lEdge, u, pcurve, curve, p, reverse, NULL );
@@ -1205,7 +1343,7 @@ bool _ViscousBuilder2D::inflate()
 {
   // Limit size of inflation step by geometry size found by
   // itersecting _LayerEdge's with _Segment's
-  double minSize = _thickness, maxSize = 0;
+  double minSize = _maxThickness, maxSize = 0;
   vector< const _Segment* > foundSegs;
   _SegmentIntersection intersection;
   for ( size_t iL1 = 0; iL1 < _polyLineVec.size(); ++iL1 )
@@ -1233,29 +1371,30 @@ bool _ViscousBuilder2D::inflate()
     }
   }
   if ( minSize > maxSize ) // no collisions possible
-    maxSize = _thickness;
+    maxSize = _maxThickness;
 #ifdef __myDEBUG
   cout << "-- minSize = " << minSize << ", maxSize = " << maxSize << endl;
 #endif
 
   double curThick = 0, stepSize = minSize;
   int nbSteps = 0;
-  if ( maxSize > _thickness )
+  if ( maxSize > _maxThickness )
-    maxSize = _thickness;
+    maxSize = _maxThickness;
   while ( curThick < maxSize )
   {
     curThick += stepSize * 1.25;
-    if ( curThick > _thickness )
+    if ( curThick > _maxThickness )
-      curThick = _thickness;
+      curThick = _maxThickness;
 
     // Elongate _LayerEdge's
     for ( size_t iL = 0; iL < _polyLineVec.size(); ++iL )
     {
       _PolyLine& L = _polyLineVec[ iL ];
       if ( !L._advancable ) continue;
+      const double lineThick = Min( curThick, getLineThickness( iL ));
       bool lenChange = false;
       for ( size_t iLE = L.FirstLEdge(); iLE < L._lEdges.size(); ++iLE )
-        lenChange |= L._lEdges[iLE].SetNewLength( curThick );
+        lenChange |= L._lEdges[iLE].SetNewLength( lineThick );
       // for ( int k=0; k<L._segments.size(); ++k)
       //   cout << "( " << L._segments[k].p1().X() << ", " <<L._segments[k].p1().Y() << " ) "
       //        << "( " << L._segments[k].p2().X() << ", " <<L._segments[k].p2().Y() << " ) "
@@ -1270,7 +1409,7 @@ bool _ViscousBuilder2D::inflate()
     {
       break; // no more inflating possible
     }
-    stepSize = Max( stepSize , _thickness / 10. );
+    stepSize = Max( stepSize , _maxThickness / 10. );
     nbSteps++;
   }
 
@@ -1533,26 +1672,28 @@ bool _ViscousBuilder2D::shrink()
           int iPFrom = L._firstPntInd, iPTo = L._lastPntInd;
           if ( isShrinkableL )
           {
+            const THypVL* hyp = getLineHypothesis( L._leftLine->_index );
             vector<gp_XY>& uvVec = L._lEdges.front()._uvRefined;
-            for ( int i = 0; i < _hyp->GetNumberLayers(); ++i ) {
+            for ( int i = 0; i < hyp->GetNumberLayers(); ++i ) {
               const UVPtStruct& uvPt = points[ iPFrom + i + 1 ];
               L._leftNodes.push_back( uvPt.node );
               uvVec.push_back ( pcurve->Value( uvPt.param ).XY() );
             }
+            iPFrom += hyp->GetNumberLayers();
           }
           if ( isShrinkableR )
           {
+            const THypVL* hyp = getLineHypothesis( L._rightLine->_index );
             vector<gp_XY>& uvVec = L._lEdges.back()._uvRefined;
-            for ( int i = 0; i < _hyp->GetNumberLayers(); ++i ) {
+            for ( int i = 0; i < hyp->GetNumberLayers(); ++i ) {
               const UVPtStruct& uvPt = points[ iPTo - i - 1 ];
               L._rightNodes.push_back( uvPt.node );
               uvVec.push_back ( pcurve->Value( uvPt.param ).XY() );
             }
+            iPTo -= hyp->GetNumberLayers();
           }
           // make proxy sub-mesh data of present nodes
           //
-          if ( isShrinkableL ) iPFrom += _hyp->GetNumberLayers();
-          if ( isShrinkableR ) iPTo   -= _hyp->GetNumberLayers();
           UVPtStructVec nodeDataVec( & points[ iPFrom ], & points[ iPTo + 1 ]);
 
           double normSize = nodeDataVec.back().normParam - nodeDataVec.front().normParam;
@@ -1723,14 +1864,14 @@ bool _ViscousBuilder2D::shrink()
             ( isR ? L._leftLine->_lEdges.back() : L._rightLine->_lEdges.front() );
           length2D = neighborLE._length2D;
           if ( length2D == 0 )
-            length2D = _thickness * nearLE._len2dTo3dRatio;
+            length2D = _maxThickness * nearLE._len2dTo3dRatio;
         }
       }
 
       // move u to the internal boundary of layers
       //  u --> u
       //  x-x-x-x-----x-----x----
-      double maxLen3D = Min( _thickness, edgeLen / ( 1 + nbAdvancable ));
+      double maxLen3D = Min( _maxThickness, edgeLen / ( 1 + nbAdvancable ));
       double maxLen2D = maxLen3D * nearLE._len2dTo3dRatio;
       if ( !length2D ) length2D = length1D / len1dTo2dRatio;
       if ( Abs( length2D ) > maxLen2D )
@@ -1746,7 +1887,8 @@ bool _ViscousBuilder2D::shrink()
 
       // compute params of layers on L
       vector<double> heights;
-      calcLayersHeight( u - u0, heights );
+      const THypVL* hyp = getLineHypothesis( L2->_index );
+      calcLayersHeight( u - u0, heights, hyp );
       //
       vector< double > params( heights.size() );
       for ( size_t i = 0; i < params.size(); ++i )
@@ -1756,13 +1898,13 @@ bool _ViscousBuilder2D::shrink()
       //  x-x-x-x---
       vector< const SMDS_MeshNode* >& layersNode = isR ? L._rightNodes : L._leftNodes;
       vector<gp_XY>& nodeUV = ( isR ? L._lEdges.back() : L._lEdges[0] )._uvRefined;
-      nodeUV.resize    ( _hyp->GetNumberLayers() );
+      nodeUV.resize    ( hyp->GetNumberLayers() );
-      layersNode.resize( _hyp->GetNumberLayers() );
+      layersNode.resize( hyp->GetNumberLayers() );
       const SMDS_MeshNode* vertexNode = nodeDataVec[ iPEnd ].node;
       const SMDS_MeshNode *  prevNode = vertexNode;
       for ( size_t i = 0; i < params.size(); ++i )
       {
-        gp_Pnt p        = curve.Value( params[i] );
+        const gp_Pnt p  = curve.Value( params[i] );
         layersNode[ i ] = helper.AddNode( p.X(), p.Y(), p.Z(), /*id=*/0, params[i] );
         nodeUV    [ i ] = pcurve->Value( params[i] ).XY();
         helper.AddEdge( prevNode, layersNode[ i ] );
@@ -1773,7 +1915,7 @@ bool _ViscousBuilder2D::shrink()
       if ( !L2->_advancable )
       {
         isRShrinkedForAdjacent = isR;
-        nodeDataForAdjacent.resize( _hyp->GetNumberLayers() );
+        nodeDataForAdjacent.resize( hyp->GetNumberLayers() );
 
         size_t iFrw = 0, iRev = nodeDataForAdjacent.size()-1, *i = isR ? &iRev : &iFrw;
         nodeDataForAdjacent[ *i ] = points[ isR ? L._lastPntInd : L._firstPntInd ];
@@ -1890,11 +2032,11 @@ bool _ViscousBuilder2D::shrink()
       {
         // refine the not shared _LayerEdge
         vector<double> layersHeight;
-        calcLayersHeight( LE2._length2D, layersHeight );
+        calcLayersHeight( LE2._length2D, layersHeight, getLineHypothesis( L2._index ));
 
         vector<gp_XY>& nodeUV2 = LE2._uvRefined;
-        nodeUV2.resize    ( _hyp->GetNumberLayers() );
+        nodeUV2.resize    ( layersHeight.size() );
-        layerNodes2.resize( _hyp->GetNumberLayers() );
+        layerNodes2.resize( layersHeight.size() );
         for ( size_t i = 0; i < layersHeight.size(); ++i )
         {
           gp_XY uv = LE2._uvOut + LE2._normal2D * layersHeight[i];
@@ -1952,12 +2094,13 @@ bool _ViscousBuilder2D::toShrinkForAdjacent( const TopoDS_Face&   adjFace,
   if ( _noShrinkVert.count( getMeshDS()->ShapeToIndex( V )) || adjFace.IsNull() )
     return false;
 
-  TopoDS_Shape hypAssignedTo;
+  vector< const StdMeshers_ViscousLayers2D* > hyps;
-  if ( const StdMeshers_ViscousLayers2D* vlHyp = findHyp( *_mesh, adjFace, &hypAssignedTo ))
+  vector< TopoDS_Shape >                      hypShapes;
+  if ( VISCOUS_2D::findHyps( *_mesh, adjFace, hyps, hypShapes ))
   {
-    VISCOUS_2D::_ViscousBuilder2D builder( *_mesh, adjFace, vlHyp );
+    VISCOUS_2D::_ViscousBuilder2D builder( *_mesh, adjFace, hyps, hypShapes );
     builder._faceSideVec = StdMeshers_FaceSide::GetFaceWires( adjFace, *_mesh, true, _error );
-    builder.findEdgesWithLayers( hypAssignedTo );
+    builder.findEdgesWithLayers();
 
     PShapeIteratorPtr edgeIt = _helper.GetAncestors( V, *_mesh, TopAbs_EDGE );
     while ( const TopoDS_Shape* edgeAtV = edgeIt->next() )
@@ -2180,7 +2323,8 @@ bool _ViscousBuilder2D::refine()
     }
 
     // normalized height of layers
-    calcLayersHeight( 1., layersHeight );
+    const THypVL* hyp = getLineHypothesis( iL );
+    calcLayersHeight( 1., layersHeight, hyp);
 
     // Create layers of faces
 
@@ -2192,11 +2336,11 @@ bool _ViscousBuilder2D::refine()
     for ( int i = L._firstPntInd; i <= L._lastPntInd; ++i )
       outerNodes[ i-L._firstPntInd ] = points[i].node;
 
-    L._leftNodes .reserve( _hyp->GetNumberLayers() );
+    L._leftNodes .reserve( hyp->GetNumberLayers() );
-    L._rightNodes.reserve( _hyp->GetNumberLayers() );
+    L._rightNodes.reserve( hyp->GetNumberLayers() );
     int cur = 0, prev = -1; // to take into account orientation of _face
     if ( isReverse ) std::swap( cur, prev );
-    for ( int iF = 0; iF < _hyp->GetNumberLayers(); ++iF ) // loop on layers of faces
+    for ( int iF = 0; iF < hyp->GetNumberLayers(); ++iF ) // loop on layers of faces
     {
       // create innerNodes of a current layer
       for ( size_t i = iN0; i < iNE; ++i )
@@ -2358,6 +2502,30 @@ bool _ViscousBuilder2D::removeMeshFaces(const TopoDS_Shape& face)
   return thereWereElems;
 }
 
+//================================================================================
+/*!
+ * \brief Returns a hypothesis for a _PolyLine
+ */
+//================================================================================
+
+const StdMeshers_ViscousLayers2D* _ViscousBuilder2D::getLineHypothesis(int iPL)
+{
+  return iPL < (int)_hypOfEdge.size() ? _hypOfEdge[ iPL ] : _hyps[0];
+}
+
+//================================================================================
+/*!
+ * \brief Returns a layers thickness for a _PolyLine
+ */
+//================================================================================
+
+double _ViscousBuilder2D::getLineThickness(int iPL)
+{
+  if ( const StdMeshers_ViscousLayers2D* h = getLineHypothesis( iPL ))
+    return Min( _maxThickness, h->GetTotalThickness() );
+  return _maxThickness;
+}
+
 //================================================================================
 /*!
  * \brief Creates a _ProxyMeshOfFace and store it in a sub-mesh of FACE
@@ -2384,21 +2552,23 @@ _ProxyMeshOfFace* _ViscousBuilder2D::getProxyMesh()
 //================================================================================
 
 void _ViscousBuilder2D::calcLayersHeight(const double    totalThick,
-                                         vector<double>& heights)
+                                         vector<double>& heights,
+                                         const THypVL*   hyp)
 {
-  heights.resize( _hyp->GetNumberLayers() );
+  const double fPowN = pow( hyp->GetStretchFactor(), hyp->GetNumberLayers() );
+  heights.resize( hyp->GetNumberLayers() );
   double h0;
-  if ( _fPowN - 1 <= numeric_limits<double>::min() )
+  if ( fPowN - 1 <= numeric_limits<double>::min() )
-    h0 = totalThick / _hyp->GetNumberLayers();
+    h0 = totalThick / hyp->GetNumberLayers();
   else
-    h0 = totalThick * ( _hyp->GetStretchFactor() - 1 )/( _fPowN - 1 );
+    h0 = totalThick * ( hyp->GetStretchFactor() - 1 )/( fPowN - 1 );
 
   double hSum = 0, hi = h0;
-  for ( int i = 0; i < _hyp->GetNumberLayers(); ++i )
+  for ( int i = 0; i < hyp->GetNumberLayers(); ++i )
   {
     hSum += hi;
     heights[ i ] = hSum;
-    hi *= _hyp->GetStretchFactor();
+    hi *= hyp->GetStretchFactor();
   }
 }
 

src/StdMeshers/StdMeshers_ViscousLayers2D.hxx

@@ -35,9 +35,10 @@ class STDMESHERS_EXPORT StdMeshers_ViscousLayers2D : public StdMeshers_ViscousLa
 {
 public:
   StdMeshers_ViscousLayers2D(int hypId, int studyId, SMESH_Gen* gen);
-
+  /*!
-  // Computes temporary 2D mesh to be used by 2D algorithm.
+   * \brief Computes temporary 2D mesh to be used by 2D algorithm.
-  // Return SMESH_ProxyMesh for the given FACE, or NULL in case of error
+   *        Return SMESH_ProxyMesh for the given FACE, or NULL in case of error
+   */
   static SMESH_ProxyMesh::Ptr Compute(SMESH_Mesh&        theMesh,
                                       const TopoDS_Face& theShape);
   /*!
@@ -46,6 +47,12 @@ public:
    */
   void RestoreListeners() const;
 
+  /*!
+   * \brief Checks compatibility of assigned StdMeshers_ViscousLayers2D hypotheses
+   */
+  static SMESH_ComputeErrorPtr CheckHypothesis(SMESH_Mesh&         aMesh,
+                                               const TopoDS_Shape& aShape,
+                                               Hypothesis_Status&  aStatus);
   /*!
    * \brief Initialize my parameter values by the mesh built on the geometry
    * \param theMesh - the built mesh