mirror of
https://git.salome-platform.org/gitpub/modules/smesh.git
synced 2024-12-28 02:10:35 +05:00
118 lines
5.0 KiB
Plaintext
118 lines
5.0 KiB
Plaintext
/*!
|
|
|
|
\page ghs3d_hypo_page GHS3D Parameters hypothesis
|
|
|
|
\n GHS3D Parameters hypothesis works only with <b>Tetrahedron (GHS3D)</b>
|
|
algorithm. This algorithm is a commercial software.
|
|
\n To get a licence, visit http://www.distene.com/corp/eval-distene.html
|
|
|
|
<h1>General parameters</h1>
|
|
|
|
\image html ghs3d_parameters_basic.png
|
|
|
|
<ul>
|
|
<li><b>Name</b> - allows to define the name of the hypothesis (GHS3D
|
|
Parameters by default).</li>
|
|
|
|
<li><b>To mesh holes</b> - if checked, the algorithm will
|
|
create mesh in the holes inside a solid shape, else only the outermost
|
|
shape will be meshed. Volumic elements created within holes are bound
|
|
to the solid.</li>
|
|
|
|
<li><b>Optimization level</b> - allows choosing the required
|
|
optimization level: none, light, medium or strong. Higher level of
|
|
optimisation provides better mesh, but can be time-consuming.
|
|
</li>
|
|
|
|
<h1>Advanced parameters</h1>
|
|
|
|
\image html ghs3d_parameters_advanced.png
|
|
|
|
<li><b>Maximum memory size</b> - launches ghs3d software with
|
|
work space limited to the specified amount of RAM, in Mbytes. If this option is
|
|
checked off, the software will be launched with 7O% of the total RAM space. </li>
|
|
|
|
<li><b>Initial memory size</b> - starts ghs3d software with
|
|
the specified amount of work space, in Mbytes. If this option is checked off, the
|
|
software will be started with 100 Megabytes of working space. </li>
|
|
|
|
<li><b>Working directory</b> - allows defining the folder for input and output
|
|
files of ghs3d software, which are the files starting with "GHS3D_" prefix. </li>
|
|
|
|
<li><b>Keep working files</b> - allows checking input and output files
|
|
of ghs3d software, while usually these files are removed after the
|
|
launch of the mesher.</li>
|
|
|
|
<li><b>Verbose level</b> - to choose verbosity level in the range from
|
|
0 to 10.
|
|
<ul> <li>0, no standard output,
|
|
</li><li>2, prints the data, quality statistics of the skin and final
|
|
meshes and indicates when the final mesh is being saved. In addition
|
|
the software gives indication regarding the CPU time.
|
|
</li><li>10, same as 2 plus the main steps in the computation, quality
|
|
statistics histogram of the skin mesh, quality statistics histogram
|
|
together with the characteristics of the final mesh.
|
|
</li></ul></li>
|
|
|
|
<li><b>To create new nodes</b> - if this option is checked off, ghs3d
|
|
tries to create tetrahedrons using only the nodes of the 2D mesh.</li>
|
|
|
|
<li><b>To remove the initial central point</b> TetMesh-GHS3D adds an internal point
|
|
at the gravity centre of the bounding box to speed up and to simplify
|
|
the meshing process. However, it is possible to refrain from creating
|
|
this point by using the command line option -no initial central point. This can be
|
|
particularly useful to generate a volume mesh without internal points at all and in some rare cases
|
|
at the boundary regeneration phase when it is impossible to proceed
|
|
with the standard options
|
|
(for example, when one dimension of the domain is more than 20 times greater than the other two).
|
|
Use this option if the boundary regeneration has failed with the standard parameters and before using
|
|
the recovery version (command line option -C).
|
|
Note: when using this option, the speed of the meshing process may
|
|
decrease, and the quality may change.
|
|
Note: the boundary regeneration may fail with this option, in some rare cases.</li>
|
|
|
|
<li><b>To use boundary recovery version</b> - enables using a
|
|
boundary recovery module which tries to
|
|
create volume meshes starting from very poor quality surface meshes
|
|
(almost flat triangles on the surface, high density propagation,
|
|
extreme aspect ratios, etc.) which fails with the standard version. The
|
|
resulting volume mesh will however most likely have a very poor
|
|
quality (poor aspect ratio of elements, tetrahedra with a very small
|
|
positive volume).</li>
|
|
|
|
<li><b>To use FEM correction</b> - Applies finite-element correction by
|
|
replacing overconstrained elements where it is possible. At first the process
|
|
slices the overconstrained edges and at second the overconstrained
|
|
facets. This ensures that there are no edges with two boundary
|
|
vertices and that there are no facets with three boundary vertices. TetMesh-GHS3D gives the initial
|
|
and final overconstrained edges and facets. It also gives the facets
|
|
which have three edges on the boundary.
|
|
Note: when using this option, the speed of the meshing process may
|
|
decrease, quality may change, and the smallest volume may be smaller.
|
|
By default, the FEM correction is not used.</li>
|
|
|
|
<li><b>Option as text</b> - allows to input in the command line any text
|
|
for ghs3d, for example, advanced options. </li>
|
|
|
|
</ul>
|
|
|
|
|
|
<h1>Enforced vertices</h1>
|
|
|
|
\image html ghs3d_enforced_vertices.png
|
|
|
|
GHS3D algorithm can locally make the mesh finer. It is possible to define enforced vertices in the volume where the mesh will be detailed.
|
|
|
|
A node will be created at the enforced vertex coordinates. There is no need to create a vertex in CAD.
|
|
|
|
An enforced vertex is defined by:
|
|
<ul>
|
|
<li>The (x,y,z) cartesian coordinates</li>
|
|
<li>A constant physical size</li>
|
|
</ul>
|
|
|
|
<br><b>See Also</b> a sample TUI Script of the \ref tui_ghs3d "creation of a Ghs3D hypothesis", including enforced vertices.
|
|
|
|
|
|
*/
|