## What is it for A stand-alone (without 3rd party servers) DPI circumvention tool. May allow to bypass http(s) website blocking or speed shaping, resist signature tcp/udp protocol discovery. The project is mainly aimed at the Russian audience to fight russian regulator named "Roskomnadzor". Some features of the project are russian reality specific (such as getting list of sites blocked by Roskomnadzor), but most others are common. Mainly OpenWRT targeted but also supports traditional Linux, FreeBSD, OpenBSD, partially MacOS. ## How it works In the simplest case you are dealing with passive DPI. Passive DPI can read passthrough traffic, inject its own packets, but cannot drop packets. If the request is prohibited the passive DPI will inject its own RST packet and optionally http redirect packet. If fake packets from DPI are only sent to client, you can use iptables commands to drop them if you can write correct filter rules. This requires manual in-deep traffic analysis and tuning for specific ISP. This is how we bypass the consequences of a ban trigger. If the passive DPI sends an RST packet also to the server, there is nothing you can do about it. Your task is to prevent ban trigger from firing up. Iptables alone will not work. This project is aimed at preventing the ban rather than eliminating its consequences. To do that send what DPI does not expect and what breaks its algorithm of recognizing requests and blocking them. Some DPIs cannot recognize the http request if it is divided into TCP segments. For example, a request of the form `GET / HTTP / 1.1 \ r \ nHost: kinozal.tv ......` we send in 2 parts: first go `GET`, then `/ HTTP / 1.1 \ r \ nHost: kinozal.tv .....`. Other DPIs stumble when the `Host:` header is written in another case: for example, `host:`. Sometimes work adding extra space after the method: `GET /` => `GET /` or adding a dot at the end of the host name: `Host: kinozal.tv.` There is also more advanced magic for bypassing DPI at the packet level. ## How to put this into practice in the linux system In short, the options can be classified according to the following scheme: 1. Passive DPI not sending RST to the server. ISP tuned iptables commands can help. This option is out of the scope of the project. If you do not allow ban trigger to fire, then you won’t have to deal with its consequences. 2. Modification of the TCP connection at the stream level. Implemented through a proxy or transparent proxy. 3. Modification of TCP connection at the packet level. Implemented through the NFQUEUE handler and raw sockets. For options 2 and 3, tpws and nfqws programs are implemented, respectively. You need to run them with the necessary parameters and redirect certain traffic with iptables. To redirect a TCP connection to a transparent proxy, the following commands are used: forwarded traffic : `iptables -t nat -I PREROUTING -i -p tcp --dport 80 -j DNAT --to 127.0.0.127:988` outgoing traffic : `iptables -t nat -I OUTPUT -o -p tcp --dport 80 -m owner ! --uid-owner tpws -j DNAT --to 127.0.0.127:988` DNAT on localhost works in the OUTPUT chain, but does not work in the PREROUTING chain without enabling the route_localnet parameter: `sysctl -w net.ipv4.conf..route_localnet=1` You can use `-j REDIRECT --to-port 988` instead of DNAT, but in this case the transparent proxy process should listen on the ip address of the incoming interface or on all addresses. Listen all - not good in terms of security. Listening one (local) is possible, but automated scripts will have to recognize it, then dynamically enter it into the command. In any case, additional efforts are required. Using route_localnet can also introduce some security risks. You make available from internal_interface everything bound to `127.0.0.0/8`. Services are usually bound to `127.0.0.1`. Its possible to deny input to `127.0.0.1` from all interfaces except lo or bind tpws to any other IP from `127.0.0.0/8` range, for example to `127.0.0.127`, and allow incomings only to that IP : ``` iptables -A INPUT ! -i lo -d 127.0.0.127 -j ACCEPT iptables -A INPUT ! -i lo -d 127.0.0.0/8 -j DROP ``` Owner filter is necessary to prevent recursive redirection of connections from tpws itself. tpws must be started under OS user `tpws`. NFQUEUE redirection of the outgoing traffic and forwarded traffic going towards the external interface, can be done with the following commands: `iptables -t mangle -I POSTROUTING -o -p tcp --dport 80 -j NFQUEUE --queue-num 200 --queue-bypass` In order not to touch the traffic to unblocked addresses, you can take a list of blocked hosts, resolve it into IP addresses and put them to ipset 'zapret', then add a filter to the command: `iptables -t mangle -I POSTROUTING -o -p tcp --dport 80 -m set --match-set zapret dst -j NFQUEUE --queue-num 200 --queue-bypass` Some DPIs catch only the first http request, ignoring subsequent requests in a keep-alive session. Then we can reduce CPU load, refusing to process unnecessary packets. `iptables -t mangle -I POSTROUTING -o -p tcp --dport 80 -m connbytes --connbytes-dir=original --connbytes-mode=packets --connbytes 1:4 -m mark ! --mark 0x40000000/0x40000000 -m set --match-set zapret dst -j NFQUEUE --queue-num 200 --queue-bypass` Mark filter does not allow nfqws-generated packets to enter the queue again. Its necessary to use this filter when also using `connbytes 1:4`. Without it packet ordering can be changed breaking the whole idea. ## ip6tables ip6tables work almost exactly the same way as ipv4, but there are a number of important nuances. In DNAT, you should take the address --to in square brackets. For example : `ip6tables -t nat -I OUTPUT -o -p tcp --dport 80 -m owner ! --uid-owner tpws -j DNAT --to [::1]:988` The route_localnet parameter does not exist for ipv6. DNAT to localhost (:: 1) is possible only in the OUTPUT chain. In the PREROUTING DNAT chain, it is possible to any global address or to the link local address of the same interface the packet came from. NFQUEUE works without changes. ## When it will not work * If DNS server returns false responses. ISP can return false IP addresses or not return anything when blocked domains are queried. If this is the case change DNS to public ones, such as 8.8.8.8 or 1.1.1.1.Sometimes ISP hijacks queries to any DNS server. Dnscrypt or dns-over-tls help. * If blocking is done by IP. * If a connection passes through a filter capable of reconstructing a TCP connection, and which follows all standards. For example, we are routed to squid. Connection goes through the full OS tcpip stack, fragmentation disappears immediately as a means of circumvention. Squid is correct, it will find everything as it should, it is useless to deceive him. BUT. Only small providers can afford using squid, since it is very resource intensive. Large companies usually use DPI, which is designed for much greater bandwidth. ## nfqws This program is a packet modifier and a NFQUEUE queue handler. For BSD systems there is dvtws. Its built from the same source and has almost the same parameters (see bsd.eng.md). nfqws takes the following parameters: ``` --debug=0|1 ; 1=print debug info --qnum= --wsize=[:] ; change window size in SYN,ACK packets. default is not to change scale factor (OBSOLETE !) --wssize=[:] ; change window size in outgoing packets. default scale factor is 0. (see CONNTRACK) --wssize-cutoff=[n|d|s]N ; apply server wsize only to packet numbers (n, default), data packet numbers (d), relative sequence (s) less than N --ctrack-timeouts=S:E:F ; internal conntrack timeouts for SYN, ESTABLISHED and FIN stages. default 60:300:60 --hostcase ; change Host: => host: --hostspell=HoSt ; exact spelling of the "Host" header. must be 4 chars. default is "host" --hostnospace ; remove space after Host: and add it to User-Agent: to preserve packet size --domcase ; mix domain case after Host: like this : TeSt.cOm --daemon ; daemonize --pidfile= ; write pid to file --user= ; drop root privs --uid=uid[:gid] ; drop root privs --dpi-desync=[[,] ; desync dpi state. modes : synack fake rst rstack disorder disorder2 split split2 ipfrag2 --dpi-desync-fwmark= ; override fwmark for desync packet. default = 0x40000000 --dpi-desync-ttl= ; set ttl for desync packet --dpi-desync-ttl6= ; set ipv6 hop limit for desync packet. by default ttl value is used --dpi-desync-fooling=none|md5sig|ts|badseq|badsum ; can take multiple comma separated values --dpi-desync-retrans=0|1 ; (fake,rst,rstack only) 0(default)=reinject original data packet after fake 1=drop original data packet to force its retransmission --dpi-desync-repeats= ; send every desync packet N times --dpi-desync-skip-nosni=0|1 ; 1(default)=do not apply desync to requests without hostname in the SNI --dpi-desync-split-pos=<1..1500> ; (for split* and disorder* only) split TCP packet at specified position --dpi-desync-ipfrag-pos-tcp=<8..9216> ; ip frag position starting from the second header (usually transport header). multiple of 8, default 8. --dpi-desync-ipfrag-pos-udp=<8..9216> ; ip frag position starting from the second header (usually transport header). multiple of 8, default 32. --dpi-desync-badseq-increment= ; badseq fooling seq signed increment. default -10000 --dpi-desync-badack-increment= ; badseq fooling ackseq signed increment. default -66000 --dpi-desync-any-protocol=0|1 ; 0(default)=desync only http and tls 1=desync any nonempty data packet --dpi-desync-fake-http= ; file containing fake http request. replacement for built-in --dpi-desync-fake-tls= ; file containing fake TLS ClientHello (for https). replacement for built-in --dpi-desync-fake-unknown= ; file containing unknown protocol fake payload. default is 256 zeroes --dpi-desync-fake-unknown-udp= ; file containing unknown udp protocol fake payload --dpi-desync-cutoff=[n|d|s]N ; apply dpi desync only to packet numbers (n, default), data packet numbers (d), relative sequence (s) less than N --hostlist= ; apply fooling only to the listed hosts (one host per line, subdomains auto apply) ``` The manipulation parameters can be combined in any way. WARNING. `--wsize` parameter is now not used anymore in scripts. TCP split can be achieved using DPI desync attack. ### DPI desync attack After completion of the tcp 3-way handshake, the first data packet from the client goes. It usually has `GET / ...` or TLS ClientHello. We drop this packet, replacing with something else. It can be a fake version with another harmless but valid http or https request (fake), tcp reset packet (rst,rstack), split into 2 segments original packet with fake segment in the middle (disorder). In articles these attack have names **TCB desynchronization** and **TCB teardown**. Fake packet must reach DPI, but do not reach the destination server. The following means are available: set a low TTL, send a packet with bad checksum, add tcp option **MD5 signature**. All of them have their own disadvantages : * md5sig does not work on all servers * badsum doesn't work if your device is behind NAT which does not pass invalid packets. The most common Linux NAT router configuration does not pass them. Most home routers are Linux based. The default sysctl configuration `net.netfilter.nf_conntrack_checksum=1` causes contrack to verify tcp and udp checksums and set INVALID state for packets with invalid checksum. Typically, iptables rules include a rule for dropping packets with INVALID state in the FORWARD chain. The combination of these factors does not allow badsum packets to pass through the router. In openwrt mentioned sysctl is set to 0 from the box, in other routers its often left in the default "1" state. For nfqws to work properly through the router set `net.netfilter.nf_conntrack_checksum=0` on the router. System never verifies checksums of locally generated packets so nfqws will always work on the router itself. If you are behind another NAT, such as a ISP, and it does not pass invalid packages, there is nothing you can do about it. But usually ISPs pass badsum. Some adapters/switches/drivers enable hardware filtering of rx badsum not allowing it to pass to the OS. This behavior was observed on a Mediatek MT7621 based device. Tried to modify mediatek ethernet driver with no luck, likely hardware enforced limitation. However the device allowed to send badsum packets, problem only existed for passthrough traffic from clients. * badseq packets will be dropped by server, but DPI also can ignore them. default badseq increment is set to -10000 because some DPIs drop packets outside of the small tcp window. But this also can cause troubles when `--dpi-desync-any-protocol` is enabled. To be 100% sure fake packet cannot fit to server tcp window consider setting badseq increment to 0x80000000 * TTL looks like the best option, but it requires special tuning for each ISP. If DPI is further than local ISP websites you can cut access to them. Manual IP exclude list is required. Its possible to use md5sig with ttl. This way you cant hurt anything, but good chances it will help to open local ISP websites. If automatic solution cannot be found then use `zapret-hosts-user-exclude.txt`. Some router stock firmwares fix outgoing TTL. Without switching this option off TTL fooling will not work. `--dpi-desync-fooling` takes multiple comma separated values. For fake,rst,rstack modes original packet can be sent after the fake one or just dropped. If its dropped OS will perform first retransmission after 0.2 sec, then the delay increases exponentially. Delay can help to make sure fake and original packets are properly ordered and processed on DPI. When `dpi-desync-retrans=1` its mandatory to use connbytes in iptables rule. Otherwise loop happens. Disorder mode splits original packet and sends packets in the following order : 1. 2nd segment 2. fake 1st segment, data filled with zeroes 3. 1st segment 4. fake 1st segment, data filled with zeroes (2nd copy) Original packet is always dropped. `--dpi-desync-split-pos` sets split position (default 2). If position is higher than packet length, pos=1 is used. This sequence is designed to make reconstruction of critical message as difficult as possible. Fake segments may not be required to bypass some DPIs, but can potentially help if more sophisticated reconstruction algorithms are used. Mode `disorder2` disables sending of fake segments. Split mode is very similar to disorder but without segment reordering : 1. fake 1st segment, data filled with zeroes 2. 1st segment 3. fake 1st segment, data filled with zeroes (2nd copy) 4. 2nd segment Mode `split2` disables sending of fake segments. It can be used as a faster alternative to --wsize. In `disorder2` and 'split2` modes no fake packets are sent, so ttl and fooling options are not required. There are DPIs that analyze responses from the server, particularly the certificate from the ServerHello that contain domain name(s). The ClientHello delivery confirmation is an ACK packet from the server with ACK sequence number corresponding to the length of the ClientHello+1. In the disorder variant, a selective acknowledgement (SACK) usually arrives first, then a full ACK. If, instead of ACK or SACK, there is an RST packet with minimal delay, DPI cuts you off at the request stage. If the RST is after a full ACK after a delay of about ping to the server, then probably DPI acts on the server response. The DPI may be satisfied with good ClientHello and stop monitoring the TCP session without checking ServerHello. Then you were lucky. 'fake' option could work. If it does not stop monitoring and persistently checks the ServerHello, --wssize parameter may help (see CONNTRACK). Otherwise it is hardly possible to overcome this without the help of the server. The best solution is to enable TLS 1.3 support on the server. TLS 1.3 sends the server certificate in encrypted form. This is recommendation to all admins of blocked sites. Enable TLS 1.3. You will give more opportunities to overcome DPI. Hosts are extracted from plain http request Host: header and SNI of ClientHello TLS message. Subdomains are applied automatically. gzip lists are supported. iptables for performing the attack on the first packet : `iptables -t mangle -I POSTROUTING -o -p tcp -m multiport --dports 80,443 -m connbytes --connbytes-dir=original --connbytes-mode=packets --connbytes 1:4 -m mark ! --mark 0x40000000/0x40000000 -j NFQUEUE --queue-num 200 --queue-bypass` This is good if DPI does not track all requests in http keep-alive session. If it does, then pass all outgoing packets for http and only first data packet for https : ``` iptables -t mangle -I POSTROUTING -o -p tcp --dport 443 -m connbytes --connbytes-dir=original --connbytes-mode=packets --connbytes 1:4 -m mark ! --mark 0x40000000/0x40000000 -j NFQUEUE --queue-num 200 --queue-bypass iptables -t mangle -I POSTROUTING -o -p tcp --dport 80 -m mark ! --mark 0x40000000/0x40000000 -j NFQUEUE --queue-num 200 --queue-bypass ``` mark is needed to keep away generated packets from NFQUEUE. nfqws sets fwmark when it sends generated packets. nfqws can internally filter marked packets. but when connbytes filter is used without mark filter packet ordering can be changed breaking the whole idea of desync attack. ### DPI desync combos dpi-desync parameter takes up to 3 comma separated arguments. zero phase means tcp connection establishement (before sending data payload). Mode can be `synack`. Hostlist filter is not applicable to the zero phase. Next phases work on packets with data payload. 1st phase mode can be `fake`,`rst`,`rstack`, 2nd phase mode - `disorder`,`disorder2`,`split`,`split2`. Can be useful for ISPs with more than one DPI. ### SYNACK mode In geneva docs it's called **TCP turnaround**. Attempt to make the DPI believe the roles of client and server are reversed. !!! This mode breaks NAT operation and can be used only if there's no NAT between the attacker's device and the DPI ! In linux it's required to remove standard firewall rule dropping INVALID packets in the OUTPUT chain, for example : `-A OUTPUT -m state --state INVALID -j DROP` In openwrt it's possible to disable the rule for both FORWARD and OUTPUT chains in /etc/config/firewall : ``` config zone option name 'wan' ......... option masq_allow_invalid '1' ``` Unfortunately there's no OUTPUT only switch. It's not desired to remove the rule from the FORWARD chain. Add the following lines to `/etc/firewall.user` : ``` iptables -D zone_wan_output -m comment --comment '!fw3' -j zone_wan_dest_ACCEPT ip6tables -D zone_wan_output -m comment --comment '!fw3' -j zone_wan_dest_ACCEPT ``` then `/etc/init.d/firewall restart` Otherwise raw sending SYN,ACK frame will cause error stopping the further processing. If you realize you don't need the synack mode it's highly suggested to restore drop INVALID rule. ### Virtual Machines Most of nfqws packet magic does not work from VMs powered by virtualbox and vmware when network is NATed. Hypervisor forcibly changes ttl and does not forward fake packets. Set up bridge networking. ### CONNTRACK nfqws is equipped with minimalistic connection tracking system (conntrack) It's enabled if some specific DPI circumvention methods are involved. Currently these are `--wssize` and `--dpi-desync-cutoff` options. Conntrack can track connection phase : SYN,ESTABLISHED,FIN , packet counts in both directions , sequence numbers. It can be fed with unidirectional or bidirectional packets. A SYN or SYN,ACK packet creates an entry in the conntrack table. That's why iptables redirection must start with the first packet although can be cut later using connbytes filter. A connection is deleted from the table as soon as it's no more required to satisfy nfqws needs or when a timeout happens. There're 3 timeouts for each connection state. They can be changed in `--ctrack-timeouts` parameter. `--wssize` changes tcp window size for the server to force it to send split replies. In order for this to affect all server operating systems, it is necessary to change the window size in each outgoing packet before sending the message, the answer to which must be split (for example, TLS ClientHello). That's why conntrack is required to know when to stop applying low window size. If you do not stop and set the low wssize all the time, the speed will drop catastrophically. Linux can overcome this using connbytes filter but other OS may not include similar filter. In http(s) case wssize stops after the first http request or TLS ClientHello. If you deal with a non-http(s) protocol you need `--wssize-cutoff`. It sets the threshold where wssize stops. Threshold can be prefixed with 'n' (packet number starting from 1), 'd' (data packet number starting from 1), 's' (relative sequence number - sent by client bytes + 1). If a http request or TLS ClientHello packet is detected wssize stops immediately ignoring wssize-cutoff option. If your protocol is prone to long inactivity, you should increase ESTABLISHED phase timeout using `--ctrack-timeouts`. Default timeout is low - only 5 mins. Don't forget that nfqws feeds with redirected packets. If you have limited redirection with connbytes ESTABLISHED entries can remain in the table until dropped by timeout. To diagnose conntrack state send SIGUSR1 signal to nfqws : `killall -SIGUSR1 nfqws`. nfqws will dump current conntrack table to stdout. Typically, in a SYN packet, client sends TCP extension **scaling factor** in addition to window size. scaling factor is the power of two by which the window size is multiplied : 0=>1, 1=>2, 2=>4, ..., 8=>256, ... The wssize parameter specifies the scaling factor after a colon. Scaling factor can only decrease, increase is blocked to prevent the server from exceeding client's window size. To force a TLS server to fragment ServerHello message to avoid hostname detection on DPI use `--wssize=1:6` The main rule is to set scale_factor as much as possible so that after recovery the final window size becomes the possible maximum. If you set `scale_factor` 64:0, it will be very slow. On the other hand, the server response must not be large enough for the DPI to find what it is looking for. Hostlist filter does not affect `--wssize` because it works since the connection initiation when it's not yet possible to extract the host name. `--wssize` may slow down sites and/or increase response time. It's desired to use another methods if possible. `--dpi-desync-cutoff` allows you to set the threshold at which it stops applying dpi-desync. Can be prefixed with 'n', 'd', 's' symbol the same way as `--wssize-cutoff`. Useful with `--dpi-desync-any-protocol=1`. If the connection falls out of the conntrack and --dpi-desync-cutoff is set, dpi desync will not be applied. Set conntrack timeouts appropriately. ### UDP support UDP attacks are limited. Its not possible to fragment UDP on transport level, only on network (ip) level. IP fragmentation is not implemented now. No protocol recognition is implemented yet so only `--dpi-desync-any-protocol` will work. Conntrack supports udp. `--dpi-desync-cutoff` will work. UDP conntrack timeout can be set in the 4th parameter of `--ctrack-timeouts`. Fake attack is useful only for stateful DPI and useless for stateless dealing with each packet independently. By default fake payload is 64 zeroes. Can be overriden using `--dpi-desync-fake-unknown-udp`. ### IP fragmentation Modern network is very hostile to IP fragmentation. Fragmented packets are often not delivered or refragmented/reassembled on the way. Frag position is set independently for tcp and udp. By default 24 and 8, must be multiple of 8. Offset starts from the header following ip header - transport header in most cases. There are important nuances when working with fragments in Linux. ipv4 : Linux allows to send ipv4 fragments but standard firewall rules in OUTPUT chain can drop them. ipv6 : There's no way for an application to reliably send fragments without defragmentation in conntrack. Sometimes it works, sometimes system defragments packets. Looks like kernels <4.16 have no simple way to solve this problem. Unloading of nf_conntrack module and its dependency nf_defrag_ipv6 helps but this severely impacts functionality. Kernels 4.16+ exclude from defragmentation untracked packets. See `blockcheck.sh` code for example. ## tpws tpws is transparent proxy. ``` --debug=0|1|2 ; 0(default)=silent 1=verbose 2=debug --bind-addr=|; for v6 link locals append %interface_name : fe80::1%br-lan --bind-iface4= ; bind to the first ipv4 addr of interface --bind-iface6= ; bind to the first ipv6 addr of interface --bind-linklocal=no|unwanted|prefer|force ; no : bind only to global ipv6 ; unwanted (default) : prefer global address, then LL ; prefer : prefer LL, then global ; force : LL only --bind-wait-ifup= ; wait for interface to appear and up --bind-wait-ip= ; after ifup wait for ip address to appear up to N seconds --bind-wait-ip-linklocal= ; accept only link locals first N seconds then any --bind-wait-only ; wait for bind conditions satisfaction then exit. return code 0 if success. --port= ; port number to listen on --socks ; implement socks4/5 proxy instead of transparent proxy --local-rcvbuf= ; SO_RCVBUF for local legs --local-sndbuf= ; SO_SNDBUF for local legs --remote-rcvbuf= ; SO_RCVBUF for remote legs --remote-sndbuf= ; SO_SNDBUF for remote legs --skip-nodelay ; do not set TCP_NODELAY for outgoing connections. incompatible with split. --no-resolve ; disable socks5 remote dns --maxconn= ; max number of local legs --maxfiles= ; max file descriptors (setrlimit). min requirement is (X*connections+16), where X=6 in tcp proxy mode, X=4 in tampering mode. ; its worth to make a reserve with 1.5 multiplier. by default maxfiles is (X*connections)*1.5+16 --max-orphan-time= ; if local leg sends something and closes and remote leg is still connecting then cancel connection attempt after N seconds --hostlist= ; only act on host in the list (one host per line, subdomains auto apply, gzip lists supported) --split-http-req=method|host ; split http request at specified logical position. --split-pos= ; split at specified pos. split-http-req takes precedence over split-pos for http reqs. --split-any-protocol ; split not only http and https --hostcase ; change Host: => host: --hostspell ; exact spelling of "Host" header. must be 4 chars. default is "host" --hostdot ; add "." after Host: name --hosttab ; add tab after Host: name --hostnospace ; remove space after Host: --hostpad= ; add dummy padding headers before Host: --domcase ; mix domain case after Host: like this : TeSt.cOm --methodspace ; add extra space after method --methodeol ; add end-of-line before method --unixeol ; replace 0D0A to 0A --daemon ; daemonize --pidfile= ; write pid to file --user= ; drop root privs --uid=uid[:gid] ; drop root privs ``` The manipulation parameters can be combined in any way. `split-http-req` takes precedence over split-pos for http reqs. split-pos works by default only on http and TLS ClientHello. use `--split-any-protocol` to act on any packet tpws can bind to multiple interfaces and IP addresses (up to 32). Port number is always the same. Parameters `--bind-iface*` and `--bind-addr` create new bind. Other parameters `--bind-*` are related to the last bind. link local ipv6 (`fe80::/8`) mode selection : ``` --bind-iface6 --bind-linklocal=no : first selects private address fd00::/8, then global address --bind-iface6 --bind-linklocal=unwanted : first selects private address fd00::/8, then global address, then LL --bind-iface6 --bind-linklocal=prefer : first selects LL, then private address fd00::/8, then global address --bind-iface6 --bind-linklocal=force : select only LL ``` To bind to all ipv4 specify `--bind-addr "0.0.0.0"`, all ipv6 - `::`. `--bind-addr=""` - mean bind to all ipv4 and ipv6. If no binds are specified default bind to all ipv4 and ipv6 addresses is created. To bind to a specific link local address do : `--bind-iface6=fe80::aaaa:bbbb:cccc:dddd%iface-name` The `--bind-wait*` parameters can help in situations where you need to get IP from the interface, but it is not there yet, it is not raised or not configured. In different systems, ifup events are caught in different ways and do not guarantee that the interface has already received an IP address of a certain type. In the general case, there is no single mechanism to hang oneself on an event of the type "link local address appeared on the X interface." To bind to a specific ip when its interface may not be configured yet do : `--bind-addr=192.168.5.3 --bind-wait-ip=20` It's possible to bind to any nonexistent address in transparent mode but in socks mode address must exist. In socks proxy mode no additional system privileges are required. Connections to local IPs of the system where tpws runs are prohibited. tpws supports remote dns resolving (curl : `--socks5-hostname` firefox : `socks_remote_dns=true`) , but does it in blocking mode. tpws uses async sockets for all activity but resolving can break this model. if tpws serves many clients it can cause trouble. also DoS attack is possible against tpws. if remote resolving causes trouble configure clients to use local name resolution and use `--no-resolve` option on tpws side. ## Ways to get a list of blocked IP 1. Enter the blocked domains to `ipset/zapret-hosts-user.txt` and run `ipset/get_user.sh` At the output, you get `ipset/zapret-ip-user.txt` with IP addresses. 2. `ipset/get_reestr_*.sh`. Russian specific 3. `ipset/get_antifilter_*.sh`. Russian specific 4. `ipset/get_config.sh`. This script calls what is written into the GETLIST variable from the config file. If the variable is not defined, then only lists for ipsets nozapret/nozapret6 are resolved. So, if you're not russian, the only way for you is to manually add blocked domains. Or write your own `ipset/get_iran_blocklist.sh` , if you know where to download this one. On routers, it is not recommended to call these scripts more than once in 2 days to minimize flash memory writes. `ipset/create_ipset.sh` executes forced ipset update. With `no-update` parameter `create_ipset.sh` creates ipset but populate it only if it was actually created. It's useful when multiple subsequent calls are possible to avoid wasting of cpu time redoing the same job. Ipset loading is resource consuming. Its a good idea to call create_ipset without `no-update` parameter only once a several days. Use it with `no-update` option in other cases. ipset scripts automatically call ip2net utility. ip2net helps to reduce ip list size by combining IPs to subnets. Also it cuts invalid IPs from the list. Stored lists are already processed by ip2net. They are error free and ready for loading. `create_ipset.sh` supports loading ip lists from gzip files. First it looks for the filename with the ".gz" extension, such as `zapret-ip.txt.gz`, if not found it falls back to the original name `zapret-ip.txt`. So your own get_iran_blockslist.sh can use "zz" function to produce gz. Study how other russian `get_XXX.sh` work. Gzipping helps saving a lot of precious flash space on embedded systems. User lists are not gzipped because they are not expected to be very large. You can add a list of domains to `ipset/zapret-hosts-user-ipban.txt`. Their ip addresses will be placed in a separate ipset "ipban". It can be used to route connections to transparent proxy "redsocks" or VPN. IPV6: if ipv6 is enabled, then additional txt's are created with the same name, but with a "6" at the end before the extension. `zapret-ip.txt` => `zapret-ip6.txt` The ipsets zapret6 and ipban6 are created. IP EXCLUSION SYSTEM. All scripts resolve `zapret-hosts-user-exclude.txt` file, creating `zapret-ip-exclude.txt` and `zapret-ip-exclude6.txt`. They are the source for ipsets nozapret/nozapret6. All rules created by init scripts are created with these ipsets in mind. The IPs placed in them are not involved in the process. zapret-hosts-user-exclude.txt can contain domains, ipv4 and ipv6 addresses or subnets. FreeBSD. `ipset/*.sh` scripts also work in FreeBSD. Instead of ipset they create ipfw lookup tables with the same names as in Linux. ipfw tables can store both ipv4 and ipv6 addresses and subnets. There's no 4 and 6 separation. LISTS_RELOAD config parameter defines a custom lists reloading command. Its useful on BSD systems with PF. LISTS_RELOAD=- disables reloading ip list backend. ## Domain name filtering An alternative to ipset is to use tpws or nfqws with a list of domains. Only one list is supported. Enter the blocked domains to `ipset/zapret-hosts-users.txt`. Remove `ipset/zapret-hosts.txt.gz`. Then the init script will run tpws with the `zapret-hosts-users.txt` list. Other option ( Roskomnadzor list - `get_hostlist.sh` ) is russian specific. You can write your own replacement for `get_hostlist.sh`. When filtering by domain name, daemons should run without filtering by ipset. When using large regulator lists estimate the amount of RAM on the router ! ## Choosing parameters The file `/opt/zapret/config` is used by various components of the system and contains basic settings. It needs to be viewed and edited if necessary. Main mode : ``` tpws - tpws transparent mode tpws-socks - tpws socks mode binds to localhost and LAN interface (if IFACE_LAN is specified or the system is OpenWRT). port 988 nfqws - nfqws filter - only fill ipset or load hostlist custom - use custom script for running daemons and establishing firewall rules ``` `MODE=tpws` Enable http fooling : `MODE_HTTP=1` Apply fooling to keep alive http sessions. Only applicable to nfqws. Tpws always fool keepalives. Not enabling this can save CPU time. `MODE_HTTP_KEEPALIVE=0` Enable https fooling : `MODE_HTTPS=1` Host filtering mode : ``` none - apply fooling to all hosts ipset - limit fooling to hosts from ipset zapret/zapret6 hostlist - limit fooling to hosts from hostlist ``` `MODE_FILTER=none` Its possible to change manipulation options used by tpws : `TPWS_OPT="--hostspell=HOST --split-http-req=method --split-pos=3"` nfqws options for DPI desync attack: ``` DESYNC_MARK=0x40000000 NFQWS_OPT_DESYNC="--dpi-desync=fake --dpi-desync-ttl=0 --dpi-desync-fooling=badsum --dpi-desync-fwmark=$DESYNC_MARK" ``` Separate nfqws options for http and https and ip protocol versions 4,6: ``` NFQWS_OPT_DESYNC_HTTP="--dpi-desync=split --dpi-desync-ttl=0 --dpi-desync-fooling=badsum" NFQWS_OPT_DESYNC_HTTPS="--wssize=1:6 --dpi-desync=split --dpi-desync-ttl=0 --dpi-desync-fooling=badsum" NFQWS_OPT_DESYNC_HTTP6="--dpi-desync=split --dpi-desync-ttl=5 --dpi-desync-fooling=none" NFQWS_OPT_DESYNC_HTTPS6="--wssize=1:6 --dpi-desync=split --dpi-desync-ttl=5 --dpi-desync-fooling=none" ``` If one of `NFQWS_OPT_DESYNC_HTTP`/`NFQWS_OPT_DESYNC_HTTPS` is not defined it takes value of NFQWS_OPT_DESYNC. If one of `NFQWS_OPT_DESYNC_HTTP6`/`NFQWS_OPT_DESYNC_HTTPS6` is not defined it takes value from `NFQWS_OPT_DESYNC_HTTP`/`NFQWS_OPT_DESYNC_HTTPS`. It means if only `NFQWS_OPT_DESYNC` is defined all four take its value. If a variable is not defined, the value `NFQWS_OPT_DESYNC` is taken. flow offloading control (OpenWRT only) ``` donttouch : disable system flow offloading setting if selected mode is incompatible with it, dont touch it otherwise and dont configure selective flow offloading none : always disable system flow offloading setting and dont configure selective flow offloading software : always disable system flow offloading setting and configure selective software flow offloading hardware : always disable system flow offloading setting and configure selective hardware flow offloading ``` `FLOWOFFLOAD=donttouch` The GETLIST parameter tells the install_easy.sh installer which script to call to update the list of blocked ip or hosts. Its called via `get_config.sh` from scheduled tasks (crontab or systemd timer). Put here the name of the script that you will use to update the lists. If not, then the parameter should be commented out. You can individually disable ipv4 or ipv6. If the parameter is commented out or not equal to "1", use of the protocol is permitted. ``` #DISABLE_IPV4=1 DISABLE_IPV6=1 ``` The number of threads for mdig multithreaded DNS resolver (1..100). The more of them, the faster, but will your DNS server be offended by hammering ? `MDIG_THREADS=30` temp directory. Used by ipset/*.sh scripts for large lists processing. /tmp by default. Can be reassigned if /tmp is tmpfs and RAM is low. TMPDIR=/opt/zapret/tmp ipset options : `IPSET_OPT="hashsize 262144 maxelem 2097152` Kernel automatically increases hashsize if ipset is too large for the current hashsize. This procedure requires internal reallocation and may require additional memory. On low RAM systems it can cause errors. Do not use too high hashsize. This way you waste your RAM. And dont use too low hashsize to avoid reallocs. ip2net options. separate for ipv4 and ipv6. ``` IP2NET_OPT4="--prefix-length=22-30 --v4-threshold=3/4" IP2NET_OPT6="--prefix-length=56-64 --v6-threshold=5" ``` Enable gzip compression for large lists. Used by ipset/*.sh scripts. `GZIP_LISTS=1` Command to reload ip/host lists after update. Comment or leave empty for auto backend selection : ipset or ipfw if present. On BSD systems with PF no auto reloading happens. You must provide your own command. Newer FreeBSD versions support table only reloading : pfctl -Tl -f /etc/pf.conf Set to "-" to disable reload. LISTS_RELOAD="pfctl -f /etc/pf.conf" In openwrt there's default network 'lan'. Only traffic coming from this network is redirected to tpws by default. To override this behaviour set the following variable : `OPENWRT_LAN="lan lan2 lan3"` The following settings are not relevant for openwrt : If your system works as a router, then you need to enter the names of the internal and external interfaces: ``` IFACE_LAN = eth0 IFACE_WAN = eth1 ``` IMPORTANT: configuring routing, masquerade, etc. not a zapret task. Only modes that intercept transit traffic are enabled. It's possible to specify multiple interfaces like this : `IFACE_LAN="eth0 eth1 eth2"` The `INIT_APPLY_FW=1` parameter enables the init script to independently apply iptables rules. With other values or if the parameter is commented out, the rules will not be applied. This is useful if you have a firewall management system, in the settings of which you should tie the rules. ## Screwing to the firewall control system or your launch system If you use some kind of firewall management system, then it may conflict with an existing startup script. When re-applying the rules, it could break the iptables settings from the zapret. In this case, the rules for iptables should be screwed to your firewall separately from running tpws or nfqws. The following calls allow you to apply or remove iptables rules separately: ``` /opt/zapret/init.d/sysv/zapret start-fw /opt/zapret/init.d/sysv/zapret stop-fw ``` And you can start or stop the demons separately from the firewall: ``` /opt/zapret/init.d/sysv/zapret start-daemons /opt/zapret/init.d/sysv/zapret stop-daemons ``` ## Installation ### Checking ISP Before running zapret you must discover working bypass strategy. `blockcheck.sh` automates this process. It first checks DNS then tries many strategies finding the working ones. Note that DNS check is mostly Russia targeted. It checks several pre-defined blocked in Russia domains and verifies system DNS answers with public DNS answers. Because ISP can block public DNS or redirect any DNS queries to their servers `blockcheck.sh` also checks that all returned answers are unique. Usually if DNS is blocked ISP returns single ip for all blocked domains to redirect you to their "access denied" page. `blockcheck.sh` works in Linux and FreeBSD. ### desktop linux system Simple install works on most modern linux distributions with systemd or openrc, OpenWRT and MacOS. Run `install_easy.sh` and answer its questions. ### OpenWRT `install_easy.sh` works on openwrt but there're additional challenges. They are mainly about possibly low flash free space. Simple install will not work if it has no space to install itself and required packages from the repo. Another challenge would be to bring zapret to the router. You can download zip from github and use it. Do not repack zip contents in Windows, because this way you break chmod and links. Install openssh-sftp-server and unzip to openwrt and use sftp to transfer the file. The best way to start is to put zapret dir to `/tmp` and run `/tmp/zapret/install_easy.sh` from there. After installation remove `/tmp/zapret` to free RAM. The absolute minimum for openwrt is 64/8 system, 64/16 is comfortable, 128/extroot is recommended. ### Android Its not possible to use nfqws and tpws in transparent proxy mode without root privileges. Without root tpws can run in --socks mode. I have no NFQUEUE presence statistics in stock android kernels, but its present on my MTK device. If NFQUEUE is present nfqws works. There's no ipset support unless you run custom kernel. In common case task of bringing up ipset on android is ranging from "not easy" to "almost impossible", unless you find working kernel image for your device. Android does not use /etc/passwd, `tpws --user` won't work. There's replacement. Use numeric uids in `--uid` option. Its recommended to use gid 3003 (AID_INET), otherwise tpws will not have inet access. Example : `--uid 1:3003` In iptables use : `! --uid-owner 1` instead of `! --uid-owner tpws`. Write your own shell script with iptables and tpws, run it using your root manager. Autorun scripts are here : magisk : `/data/adb/service.d` supersu : `/system/su.d` I haven't checked whether android can kill iptable rules at its own will during wifi connection/disconnection, mobile data on/off, ... How to run tpws on root-less android. You can't write to `/system`, `/data`, can't run from sd card. Selinux prevents running executables in `/data/local/tmp` from apps. Use adb and adb shell. ``` mkdir /data/local/tmp/zapret adb push tpws /data/local/tmp/zapret chmod 755 /data/local/tmp/zapret /data/local/tmp/zapret/tpws chcon u:object_r:system_file:s0 /data/local/tmp/zapret/tpws ``` Now its possible to run `/data/local/tmp/zapret/tpws` from any app such as tasker. ### FreeBSD, OpenBSD, MacOS see docs/bsd.eng.md ### Windows (WSL) Using WSL (Windows subsystem for Linux) it's possible to run tpws in socks mode under rather new builds of windows 10 and windows server. Its not required to install any linux distributions as suggested in most articles. tpws is static binary. It doesn't need a distribution. Install WSL : `dism.exe /online /enable-feature /featurename:Microsoft-Windows-Subsystem-Linux /all` Copy binaries/x86_64/tpws_wsl.tgz to the target system. Run : `wsl --import tpws "%USERPROFILE%\tpws" tpws_wsl.tgz` Run tpws : `wsl --exec /tpws --uid=1 --no-resolve --socks --bind-addr=127.0.0.1 --port=1080 ` Configure socks as 127.0.0.1:1080 in a browser or another program. Cleanup : `wsl --unregister tpws` Tested in windows 10 build 19041 (20.04). NOTICE. There is native windows solution GoodByeDPI. It works on packet level like nfqws. ### Other devices Author's goal does not include easy supporting as much devices as possibles. Please do not ask for easy supporting firmwares. It requires a lot of work and owning lots of devices. Its counterproductive. As a devices owner its easier for you and should not be too hard if firmware is open. Most closed stock firmwares are not designed for custom usage and sometimes actively prevent it. In the latter case you have to hack into it and reverse engineer. Its not easy. Binaries are universal. They can run on almost all firmwares. You will need : * root shell access. true sh shell, not microtik-like console * startup hook * r/w partition to store binaries and startup script with executable permission (+x) * tpws can be run almost anywhere but nfqws require kernel support for NFQUEUE. Its missing in most firmwares. * too old 2.6 kernels are unsupported and can cause errors. newer 2.6 kernels are OK. If binaries crash with segfault (rare but happens on some kernels) try to unpack upx like this : upx -d tpws. First manually debug your scenario. Run iptables + daemon and check if its what you want. Write your own script with iptables magic and run required daemon from there. Put it to startup. Dont ask me how to do it. Its different for all firmwares and requires studying. Find manual or reverse engineer yourself. Check for race conditions. Firmware can clear or modify iptables after your startup script. If this is the case then run another script in background and add some delay there.